Agilent Varian AGD-100 Active Vacuum Pressure Gauge Digital Control Unit, Single Channel, One Vacuum Sensor Compatible with FRG 700, FRG702, PCG750, PCG752, PVG500, PVG502, PVG550, and PVG552 Gauges Agilent Varian Part Number AGD100 The Agilent Varian AGD-100 low cost option active vacuum pressure gauge digital display unit is used together with Agilent Varian vacuum pressure gauge sensors for a total pressure measurement system. This single channel display unit will measure Agilent Varian vacuum gauges (RG 700, FRG702, PCG750, PCG752, PVG500, PVG502, PVG550, and PVG552 gauge sensors) and has adjustable set point control. The AGD-100 is suited for incorporation into a 19 rack or a control panel or for use as desk-top unit. The Agilent Varian AGD-100 has only 1 connection for gauges, it is the RJ45 8 pin female connector. Pressure range is from 103 Torr to 10-10 Torr depending on sensor gauge. Pressure Units are measured in mbar, Pa, or Torr. Input voltage is 90-250 VAC 50/60 hz. For a complete .pdf instruction manual on the AGD-100 scroll down to (AVAILABLE DOWNLOADS) The following Agilent Varian gauge sensors are compatible with the AGD-100: Pirani PVG (PVG-500, PVG-502, PVG-550, PVG-552) Pirani/Capacitive PCG (PCG-750, PCG-752) Cold cathode/Pirani FRG (FRG-700, FRG-702)

Agilent Varian AGC-100 Active Vacuum Pressure Gauge Controller Unit, Single Channel, One Vacuum Sensor Compatible with FRG 700/702/720/730, PCG750, PCG752, PVG500, PVG502, PVG550, PVG552, and CDG500 Agilent Varian Part Number AGC100 The Agilent Varian AGC-100 active gauge digital control unit is used together with Agilent Varian vacuum gauges for total pressure measurement system. This single channel controller unit will measure pressure from either FRG, PCG, PVG and CDG Agilent Varian active vacuum gauges sensors and has adjustable set point control. The AGC-100 is suited for incorporation into a 19 rack or a control panel or for use as desk-top unit. The Agilent Varian AGC-100 has provisions for 2 different type gauge sensor connections. The first is the 15 pin D-Sub female connector. The Second is the RJ45 8 pin female connector. CAUTION: Only one gauge sensor should be connected at any time, connecting two gauge sensors may cause gauge damage. Pressure range is from 103 Torr to 10-10 Torr depending on sensor gauge. Pressure Units are measured in mbar, Pa, Torr, or Micron. Input voltage is 90-250 VAC 50/60 hz. For a complete .pdf instruction manual on the AGC-100 scroll down to (AVAILABLE DOWNLOADS) The following Agilent Varian gauge sensors are compatible with the AGC-100: Pirani PVG (PVG-500, PVG-502, PVG-550, PVG-552) Pirani/Capacitive PCG (PCG-750, PCG-752) Capacitive CDG (CDG-500) Cold cathode/Pirani FRG (FRG-700, FRG-702) Hot cathode/Pirani FRG (FRG-720, FRG-730)

Agilent Varian CDG-500 Capacitance Diaphragm Gauge Cable, 10 ft (3 Meters) PN AGCCBL303 This is the Agilent Varian CDG-500 Capacitance Diaphragm Gauge Cable, 10 ft. (3 Meters). Works with ALL Agilent Varian CDG-500 Capacitance Diahragm Gauges. Other guage cables can be found on this website by doing a search with the manufacture part number in our search engine. Can be used with the following Agilent Varian Controllers: XGS-600 Controller Active Gauge Controller ACG-100, AGD-100

Agilent Varian FRG700, FRG702 or PVG500 Piriani Combination Gauge Cable, 10 ft, 3 Meters PN AGCCBL103 This is the FRG700 FRG702 or PVG500 Piriani Combination Gauge Cable, 10 ft. (3 Meters). Works with ALL Agilent Varian FRG700, FRG702 or PVG500 Gauges. Other guage cables can be found on this website by doing a search with the manufacture part number in our search engine. Can be used with the following Agilent Varian Controllers: XGS-600 Controller Active Gauge Controller ACG-100, AGD-100

Agilent Varian FRG-720 or FRG-730 Cold Cathode Pirani Combination Full Range Gauge Cable, 10 ft (3 Meters) PN AGCCBL203 This is the Agilent Varian FRG-720 FRG-730 Cold Cathode Pirani Combination Full Range Gauge Cable, 10 ft. (3 Meters). Works with ALL Agilent Varian FRG-720 or FRG-730 Combination Bayard Alpert, Pirani Cold Cathode Gauges. Can be used with the following Agilent Varian Controllers: XGS-600 Controller Active Gauge Controller ACG-100

Agilent Varian Front Rack Adapter for Active Gauge Controllers AGC100, AGD100, AGC100ADPT Agilent Varian Part Number AGC100ADPT This is an adapter panel for the AGD100 or AGC100 Active Gauge Controller. To install see middle graphic above. For more mounting instructions for the Active Gauge Controller see the Instruction Manual .pdf below.

Serial to USB Cable Connectivity Kit for IVP XG-120 and Other Controllers, Connects Serial RS232 to ComputerThis cable connectivity kit is needed for transferring data from an Ideal Vacuum XG-120 digital thermocouple gauge controller or any other controller with a serial output to a remote PLC or computer via RS232 serial communication, when the computer does not have a serial port. Most modern machines do not have a built in serial port, but do have a USB port. This kit consists of a 6 ft. Serial-to-USB cable and null modem adapter (controller sold separately). The cable’s DB9 male connector attaches through the null modem adapter onto the back of the controller, which has a DB9 female connector. The USB 2.0 type A connector plugs in to the computer’s USB port. Some controllers may have a DB25 serial interface in which case a DB25-to-DB9 adapter would be required. Controllers with serial interfaces include: IVP XG-120 Thermocouple Gauge Controller P108447, P108370 Agilent Varian RGC-150 Rough Thermocouple Gauge Controller, P105092 Agilent XGS-600 Vacuum Gauge Controller, P104122 Edwards Active Digital Pressure Controller, P107267 Edwards TIC Instrument Controller, P107177 Our serial-to-USB cable uses the FTDI chipset for ultimate compatibility with virtually all recent Windows, Mac and Linux platforms. Windows has built in drivers for the FTDI chipset. A variety of free, readily available, RS232 terminal software is available for online download, including PuTTY and TERMITE, which allows you to remotely monitor the output of vacuum pressure readings. Instructions for connecting and monitoring the XG-120 via RS232 serial communication are located here in the PDF downloads.