Skip to main content
× Home Services Products Catalogs Downloads TechSupport About Contact Careers (505) 872-0037

(505) 872-0037

Shopping Cart Icon
Cart
 
Login Icon
Login
Language Selector
en-it
Agilent IDP-15 Dry Scroll Vacuum Pumps On Sale Pfeiffer ASM340 Leak Detectors On Sale Agilent IDP-10 Dry Scroll Vacuum Pumps On Sale Edwards nXR Multi Stage Roots Pumps On Sale Agilent IDP-7 Dry Scroll Vacuum Pumps On Sale Ideal Vacuum XG-120 Digital Thermocouple Gauges On Sale

Keyword       Part Number:      

× Vacuum Pumps Modular Vacuum Chambers Stainless Steel Vacuum Chambers Aluminum Vacuum Chambers ExploraVAC Unlimited Chambers ExploraVAC Vacuum Chambers Fittings and Flanges Feedthroughs Vacuum Valves Rebuild Kits, Parts, And Motors Vacuum Fluids, Oils, and Greases Turbo Pumps And Controllers Filters Traps and Silencers Convection and Vacuum Ovens Leak Detection and RGA Vacuum Pressure Measurement Recirculating Chillers And Water Baths
×

Load

Ideal Vacuum UltraLock High Vacuum HV Manually Operated Gate Valve ISO-F DN 63 Flange, Ball Groove Locking, Viton Gate & Bonnet Seals, 304 Stainless Steel
In Stock
8


Ideal Vacuum UltraLock High Vacuum HV Manually Operated Gate Valve ISO-F DN 63 Flange, Ball Groove Locking, Viton Gate & Bonnet Seals, 304 Stainless Steel. ISO-63 Bolt Down Flange with M8 x 1.25 Threads These Ideal Vacuum UltraLock™ manually operated gate valves have an ISO-F DN 63 vacuum flange with M8 x 1.25 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. Our new UltraLock series of premium manually operated vacuum gate valves are built using an innovative ball-and-groove locking mechanism and have a typical life of 300,000 cycles before needing service. They are made with corrosion resistant 304 stainless-steel gates and valve bodies. All of our UltraLock series of manually operated gate valves include a visible external position indicator - the white ring conveniently mounted below the actuator. UltraLock Locking Mechanism: Our UltraLock high vacuum gate valves employ an ingenious ball-and-groove mechanism to lock the valve. Inside the valve body is a rolling carriage with lubricated ball bearings on which the gate is attached. When the valve is actuated, the carriage and gate are slid towards the vacuum port until the carriage reaches the end of the valve body. This positions the gate concentric to the port. Continued pressure on the carriage causes a set of stainless-steel balls, riding in a decreasing depth groove between the carriage and the gate, to exert outward pressure on the gate. This outward force pushes the gate into its closed position. A leak-tight seal is obtained as the outward pressure forces the gate’s O-ring seal to be pressed against the valve body’s sealing surface. It is common for these valves to achieve an extended life of 300,000 cycles before service is needed. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.

Condition: New



Part Number: P1013066



Price: €2,804.54




Currency: Euro (Euro)

Ideal Vacuum UltraLock High Vacuum HV Manually Operated Gate Valve ISO-F DN 100 Flange, Ball Groove Locking, Viton Gate & Bonnet Seals, 304 Stainless Steel
In Stock
11


Ideal Vacuum UltraLock High Vacuum UHV Manually Operated Gate Valve ISO-F DN 100 Flange, Ball Groove Locking, Viton Gate & Bonnet Seals, 304 Stainless Steel. ISO-100 Bolt Down Flange with M8 x 1.25 Threads These Ideal Vacuum UltraLock™ manually operated gate valves have an ISO-F DN 100 vacuum flange with M8 x 1.25 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. Our new UltraLock series of premium manually operated vacuum gate valves are built using an innovative ball-and-groove locking mechanism and have a typical life of 300,000 cycles before needing service. They are made with corrosion resistant 304 stainless-steel gates and valve bodies. All of our UltraLock series of manually operated gate valves include a visible external position indicator - the white ring conveniently mounted below the actuator. UltraLock Locking Mechanism: Our UltraLock high vacuum gate valves employ an ingenious ball-and-groove mechanism to lock the valve. Inside the valve body is a rolling carriage with lubricated ball bearings on which the gate is attached. When the valve is actuated, the carriage and gate are slid towards the vacuum port until the carriage reaches the end of the valve body. This positions the gate concentric to the port. Continued pressure on the carriage causes a set of stainless-steel balls, riding in a decreasing depth groove between the carriage and the gate, to exert outward pressure on the gate. This outward force pushes the gate into its closed position. A leak-tight seal is obtained as the outward pressure forces the gate’s O-ring seal to be pressed against the valve body’s sealing surface. It is common for these valves to achieve an extended life of 300,000 cycles before service is needed. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.

Condition: New



Part Number: P1013068



Price: €2,883.17




Currency: Euro (Euro)

Ideal Vacuum UltraLock High Vacuum HV Manually Operated Gate Valve ISO-F DN 160 Flange, Ball Groove Locking, Viton Gate & Bonnet Seals, 304 Stainless Steel
Out of Stock
Expecting 10
Anticipated Arrival 10 on 2024-12-27


Ideal Vacuum UltraLock High Vacuum HV Manually Operated Gate Valve ISO-F DN 160 Flange, Ball Groove Locking, Viton Gate & Bonnet Seals, 304 Stainless Steel. ISO-160 Bolt Down Flange with M10 x 1.50 Threads These Ideal Vacuum UltraLock™ manually operated gate valves have an ISO-F DN 160 vacuum flange with M10 x 1.50 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. Our new UltraLock series of premium manually operated vacuum gate valves are built using an innovative ball-and-groove locking mechanism and have a typical life of 300,000 cycles before needing service. They are made with corrosion resistant 304 stainless-steel gates and valve bodies. All of our UltraLock series of manually operated gate valves include a visible external position indicator - the white ring conveniently mounted below the actuator. UltraLock Locking Mechanism: Our UltraLock high vacuum gate valves employ an ingenious ball-and-groove mechanism to lock the valve. Inside the valve body is a rolling carriage with lubricated ball bearings on which the gate is attached. When the valve is actuated, the carriage and gate are slid towards the vacuum port until the carriage reaches the end of the valve body. This positions the gate concentric to the port. Continued pressure on the carriage causes a set of stainless-steel balls, riding in a decreasing depth groove between the carriage and the gate, to exert outward pressure on the gate. This outward force pushes the gate into its closed position. A leak-tight seal is obtained as the outward pressure forces the gate’s O-ring seal to be pressed against the valve body’s sealing surface. It is common for these valves to achieve an extended life of 300,000 cycles before service is needed. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.

Condition: New



Part Number: P1013070



Price: €3,361.08




Currency: Euro (Euro)

Ideal Vacuum UltraLock High Vacuum HV Manually Operated Gate Valve ISO-F DN 200 Flange, Ball Groove Locking, Viton Gate & Bonnet Seals, 304 Stainless Steel
In Stock
3


Ideal Vacuum UltraLock Ultra-High Vacuum UHV Manually Operated Gate Valve ISO-F DN 200 Flange, Ball Groove Locking, Viton Gate & Bonnet Seals, 304 Stainless Steel. ISO-200 Bolt Down Flange with M10 x 1.50 Threads These Ideal Vacuum UltraLock™ manually operated gate valves have an ISO-F DN 200 vacuum flange with M10 x 1.50 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. Our new UltraLock series of premium manually operated vacuum gate valves are built using an innovative ball-and-groove locking mechanism and have a typical life of 300,000 cycles before needing service. They are made with corrosion resistant 304 stainless-steel gates and valve bodies. All of our UltraLock series of manually operated gate valves include a visible external position indicator - the white ring conveniently mounted below the actuator. UltraLock Locking Mechanism: Our UltraLock high vacuum gate valves employ an ingenious ball-and-groove mechanism to lock the valve. Inside the valve body is a rolling carriage with lubricated ball bearings on which the gate is attached. When the valve is actuated, the carriage and gate are slid towards the vacuum port until the carriage reaches the end of the valve body. This positions the gate concentric to the port. Continued pressure on the carriage causes a set of stainless-steel balls, riding in a decreasing depth groove between the carriage and the gate, to exert outward pressure on the gate. This outward force pushes the gate into its closed position. A leak-tight seal is obtained as the outward pressure forces the gate’s O-ring seal to be pressed against the valve body’s sealing surface. It is common for these valves to achieve an extended life of 300,000 cycles before service is needed. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.

Condition: New



Part Number: P1013072



Price: €4,464.00




Currency: Euro (Euro)

Ideal Vacuum UltraLock High Vacuum HV Manually Operated Gate Valve ISO-F DN 250 Flange, Ball Groove Locking, Viton Gate & Bonnet Seals, 304 Stainless Steel
In Stock
2
Expecting 5
Anticipated Arrival 5 on 2024-11-30


Ideal Vacuum UltraLock High Vacuum HV Manually Operated Gate Valve ISO-F DN 250 Flange, Ball Groove Locking, Viton Gate & Bonnet Seals, 304 Stainless Steel. ISO-250 Bolt Down Flange with M10 x 1.50 Threads These Ideal Vacuum UltraLock™ manually operated gate valves have an ISO-F DN 250 vacuum flange with M10 x 1.50 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. Our new UltraLock series of premium manually operated vacuum gate valves are built using an innovative ball-and-groove locking mechanism and have a typical life of 300,000 cycles before needing service. They are made with corrosion resistant 304 stainless-steel valve bodies and aluminum gates for weight reduction. All of our UltraLock series of manually operated gate valves include a visible external position indicator - the white ring conveniently mounted below the actuator. UltraLock Locking Mechanism: Our UltraLock high vacuum gate valves employ an ingenious ball-and-groove mechanism to lock the valve. Inside the valve body is a rolling carriage with lubricated ball bearings on which the gate is attached. When the valve is actuated, the carriage and gate are slid towards the vacuum port until the carriage reaches the end of the valve body. This positions the gate concentric to the port. Continued pressure on the carriage causes a set of stainless-steel balls, riding in a decreasing depth groove between the carriage and the gate, to exert outward pressure on the gate. This outward force pushes the gate into its closed position. A leak-tight seal is obtained as the outward pressure forces the gate’s O-ring seal to be pressed against the valve body’s sealing surface. It is common for these valves to achieve an extended life of 300,000 cycles before service is needed. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.

Condition: New



Part Number: P1013074



Price: €6,835.50




Currency: Euro (Euro)

Bolt Kit for ISO-F DN 63 Gate Valve with Threaded Hole Flange, Includes 4 Silver Plated M8 x 1.25 x 20 mm Long Bolts and 4 Stainless Steel Washers
In Stock
106


Bolt Kit for ISO-F DN 63 Gate Valve with Threaded Hole Flange, Includes 4 Silver Plated M8 x 1.25 x 20 mm Long Bolts and 4 Stainless Steel Washers. These bolt kits consist of 4 hex head, silver plated M8 x 1.25 bolts, 20 mm long, and 4 stainless steel flat washers. They are properly sized for connecting ISO-F 63 hole through flanges and fittings to the threaded holes in ISO 63 gate valves. Gate valves have standardized flange, thread, and thread depth specifications. These bolt kits are correct for connecting any gate valve of this flange type and size to an unthreaded flange of the same size, no matter the manufacturer. A centering ring with O-ring seal is required and sold separately (part number P101761). The length of the bolts in this kit are specially measured so they tighten ISO-F to ISO-F flanges fully but don’t bottom out in the blind threaded holes of the gate valve’s flange. The bolts are silver plated to prevent galling or seizing of the bolts and to make them easier to loosen, especially if they have been heated to bakeout temperatures. If the gate valve is to be connected/adapted to an ISO-K type flange, such as might be found on a turbo pump, single claw clamps with longer bolts and centering rings are required.

Condition: New



Part Number: P1013154



Price: €12.28




Currency: Euro (Euro)

Bolt Kit for ISO-F DN 100 Gate Valve with Threaded Hole Flange, Includes 8 Silver Plated M8 x 1.25 x 20 mm Long Bolts and 8 Stainless Steel Washers.
In Stock
53


Bolt Kit for ISO-F DN 100 Gate Valve with Threaded Hole Flange, Includes 8 Silver Plated M8 x 1.25 x 20 mm Long Bolts and 8 Stainless Steel Washers, 1.25 mm Pitch. These bolt kits consist of 8 hex head, silver plated M8 x 1.25 bolts, 20 mm long, and 8 stainless steel flat washers. They are properly sized for connecting ISO-F 100 hole through flanges and fittings to the threaded holes in ISO 100 gate valves. Gate valves have standardized flange, thread, and thread depth specifications. These bolt kits are correct for connecting any gate valve of this flange type and size to an unthreaded flange of the same size, no matter the manufacturer. A centering ring with O-ring seal is required and sold separately. The length of the bolts in this kit are specially measured so they tighten ISO-F to ISO-F flanges fully but don’t bottom out in the blind threaded holes of the gate valve’s flange. The bolts are silver plated to prevent galling or seizing of the bolts and to make them easier to loosen, especially if they have been heated to bakeout temperatures. If the gate valve is to be connected/adapted to an ISO-K type flange, such as might be found on a turbo pump, single claw clamps with longer bolts and centering rings are required. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange sizes of NW-100. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-80, NW-100, Vacuum Flanges, Silver-Plated, Quantity of 8ISO-LF Flange Size: NW-100Quantity: 8 bolts include washersCommon Dimensions: Bolt Size M8 x 20 x 1.25mm Pitch

Condition: New



Part Number: P1013155



Price: €15.91




Currency: Euro (Euro)

Bolt Kit for ISO-F DN 80 Gate Valve with Tapped Hole Flange, Includes 8 Silver Plated M8 x 1.25 x 20 mm Long Bolts and 8 Stainless Steel Washers.
In Stock
53


Bolt Kit for ISO-F DN 80 Gate Valve with Threaded Hole Flange, Includes 8 Silver Plated M8 x 1.25 x 20 mm Long Bolts and 8 Stainless Steel Washers. 1.25 mm Pitch. These bolt kits consist of 8 hex head, silver plated M8 x 1.25 bolts, 20 mm long, and 8 stainless steel flat washers. They are properly sized for connecting ISO-F 80 hole through flanges and fittings to the threaded holes in ISO 80 gate valves. Gate valves have standardized flange, thread, and thread depth specifications. These bolt kits are correct for connecting any gate valve of this flange type and size to an unthreaded flange of the same size, no matter the manufacturer. A centering ring with O-ring seal is required and sold separately. The length of the bolts in this kit are specially measured so they tighten ISO-F to ISO-F flanges fully but don’t bottom out in the blind threaded holes of the gate valve’s flange. The bolts are silver plated to prevent galling or seizing of the bolts and to make them easier to loosen, especially if they have been heated to bakeout temperatures. If the gate valve is to be connected/adapted to an ISO-K type flange, such as might be found on a turbo pump, single claw clamps with longer bolts and centering rings are required. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange sizes of NW-80. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-80, NW-100, Vacuum Flanges, Silver-Plated, Quantity of 8ISO-LF Flange Size: NW-80Quantity: 8 bolts include washersCommon Dimensions: Bolt Size M8 x 20 x 1.25mm Pitch

Condition: New



Part Number: P1013180



Price: €15.91




Currency: Euro (Euro)

Bolt Kit for ISO-F DN 160 Gate Valve with Tapped Hole Flange, Includes 8 Silver Plated M10 x 1.50 x 25 mm Long Bolts and 8 Stainless Steel Washers.
In Stock
37


ISO-F DN 160 Bolt Set, for Ideal Vacuum UltraLock Gate Valves Tapped Holes, Metric M10 x 25 mm Long Bolts, 1.50 mm Pitch, Silver-Plated, Quantity of 8 washers included. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange sizes of NW-160. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-160, Vacuum Flanges, Silver-Plated, Quantity of 8ISO-LF Flange Size: NW-160Quantity: 8 bolts include washersCommon Dimensions: Bolt Size M10 x 30 x 1.50mm Pitch

Condition: New



Part Number: P1013156



Price: €18.17




Currency: Euro (Euro)

Bolt Kit for ISO-F DN 200 Gate Valve with Tapped Hole Flange, Includes 12 Silver Plated M10 x 1.50 x 25 mm Long Bolts and 12 Stainless Steel Washers.
In Stock
24


Bolt Kit for ISO-F DN 200 Tapped Holes Gate Valve Flange, Threaded Holes, Includes Twelve M10 x 1.50 x 25 mm Long Silver Plated Bolts and Twelve Washers, 1.50 mm Pitch. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange sizes of NW-200. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-200, Vacuum Flanges, Silver-Plated, Quantity of 12ISO-LF Flange Size: NW-200Quantity: 12 bolts include washersCommon Dimensions: Bolt Size M10 x 30 x 1.50mm Pitch

Condition: New



Part Number: P1013157



Price: €24.47




Currency: Euro (Euro)

Bolt Kit for ISO-F DN 250 Gate Valve with Tapped Hole Flange, Includes 12 Silver Plated M10 x 1.50 x 35 mm Long Bolts and 12 Stainless Steel Washers.
In Stock
24


ISO-F DN 250 Bolt Set, for Ideal Vacuum UltraLock Gate Valves Tapped Holes, Metric M10 x 35 mm Long Bolts, 1.50 mm Pitch, Silver-Plated, Quantity of 12 bolts washers included. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange size NW-250. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-250, Vacuum Flanges, Silver-Plated, Quantity of 12ISO-LF Flange Size: NW-250Quantity: 12 bolts include washersCommon Dimensions: Bolt Size M10 x 40 x 1.50mm Pitch

Condition: New



Part Number: P1013158



Price: €28.45




Currency: Euro (Euro)

ISO 63 Centering Ring Aluminum with Viton O-Ring, NW-63 Vacuum Flange Size, Typically Used with 2.5 Inch O.D. (63.50 mm) Tubing
In Stock
179


ISO 63 Centering Ring Aluminum with Viton® O-Ring, NW-63 Vacuum Flange Size, Typically Used With 2.5 Inch O.D. (63.50 mm) Tubing. These ISO DN 63 centering rings are made of aluminum with durable Viton® (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 63 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material.ISO DN 63 Centering Ring, for Sealing of NW-63 Vacuum Flanges, Aluminum with Viton® O-Ring (FPM) ISO-LF Flange Size: NW-63Common Dimensions:A = 2.75" (70.00mm) B = 0.15" (3.90mm)

Condition: New



Part Number: P101766



Price: €48.94




Currency: Euro (Euro)

ISO 100 Centering Ring Aluminum with Viton O-Ring, NW-100 Vacuum Flange Size, Typically Used with 4 Inch O.D. (101.6 mm) Tubing
In Stock
245


ISO 100 Centering Ring Aluminum with Viton® O-Ring, NW-100 Vacuum Flange Size, Typically Used with 4 Inch O.D. (101.6 mm) Tubing These ISO DN 100 centering rings are made of aluminum with durable Viton® (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 100 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material. ISO DN 100 Centering Ring, for Sealing of NW-100 Vacuum Flanges, Aluminum with Viton® O-Ring (FPM) ISO-LF Flange Size: NW-100 Common Dimensions:A = 4.01" (102.00 mm) B = 0.15" (3.9 mm)

Condition: New



Part Number: P101768



Price: €54.83




Currency: Euro (Euro)

ISO 160 Centering Ring Aluminum with Viton O-Ring, NW-160 Vacuum Flange Size, Typically Used with 6 Inch O.D. (152.4 mm) Tubing
In Stock
156


ISO 160 Centering Ring Aluminum with Viton® O-Ring, NW-160 Vacuum Flange Size, Typically Used with 6 Inch O.D. (152.4 mm) Tubing These ISO DN 160 centering rings are made of aluminum with durable Viton® (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 160 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material. ISO DN 160 Centering Ring, for Sealing of NW-160 Vacuum Flanges, Aluminum with Viton® O-Ring (FPM) ISO-LF Flange Size: NW-160 Common Dimensions:A = 6.02" (153.00 mm) B = 0.15" (3.9 mm)

Condition: New



Part Number: P101769



Price: €76.50




Currency: Euro (Euro)

ISO 200 Centering Ring Aluminum with Viton O-Ring, NW-200 Vacuum Flange Size, Typically Used with 8 Inch O.D. (203.2 mm) Tubing
In Stock
96


ISO 200 Centering Ring Aluminum with Viton® O-Ring, NW-200 Vacuum Flange Size, Typically Used with 8 Inch O.D. (203.2 mm) Tubing These ISO DN 200 centering rings are made of aluminum with durable Viton® (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 200 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material. ISO DN 200 Centering Ring, for Sealing of NW-200 Vacuum Flanges, Aluminum with Viton® O-Ring (FPM) ISO-LF Flange Size: NW-200 Common Dimensions:A = 8.38" (213.00 mm) B = 0.15" (3.9 mm)

Condition: New



Part Number: P101770



Price: €102.57




Currency: Euro (Euro)

ISO 250 Centering Ring Aluminum with Viton O-Ring, NW-250 Vacuum Flange Size, Typically Used with 10 Inch O.D. (254 mm) Tubing
In Stock
35


ISO 250 Centering Ring, NW-250 Vacuum Flange Size, Aluminum with Viton® O-Ring, Typically Used with 10 Inch O.D. (254 mm) Tubing. These ISO DN 250 centering rings are made of aluminum with durable Viton® (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 250 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material. ISO DN 250 Centering Ring, for Sealing of NW-250 Vacuum Flanges, Aluminum with Viton® O-Ring (FPM) ISO-LF Flange Size: NW-250 Common Dimensions:A = 10.28" (261.00 mm) B = 0.15" (3.90mm)

Condition: New



Part Number: P1012741



Price: €107.97




Currency: Euro (Euro)
Marca de agua con el logotipo de Ideal Vacuum
CONTACT US
Ideal Vacuum Products , LLC
5910 Midway Park Blvd NE
Albuquerque, New Mexico 87109-5805 USA

Phone: (505) 872-0037
Fax: (505) 872-9001
info@idealvac.com
© 2003 - 2024 Ideal Vacuum Products LLC. All rights reserved.