Keyword Part Number:
Ideal Vacuum UltraLock High Vacuum HV Pneumatic Gate Valve ISO-F DN 63 Flange, Ball Groove Locking, Viton Seals, 304 Stainless Steel. ISO-63 Bolt Down Flange with M8 x 1.25 Threads. Includes Reed Switch Position Indicators. These Ideal Vacuum UltraLock™ pneumatically operated gate valves have an ISO-F DN 63 vacuum flange with M8 x 1.25 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. Our new UltraLock series of premium pneumatically operated vacuum gate valves are built using an innovative ball-and-groove locking mechanism which keeps the valve locked closed during loss of power or air pressure, while reducing wear and extending operating life. These UltraLock gate valves have a typical life of 300,000 cycles before needing service and are made with corrosion resistant 304 stainless-steel gates and valve bodies. An easily visible external position indicator and position sensor switches are standard on all pneumatic UltraLock gate valves.UltraLock Locking Mechanism: Our UltraLock high vacuum gate valves employ an ingenious ball-and-groove mechanism to lock the valve. Inside the valve body is a rolling carriage with lubricated ball bearings on which the gate is attached. When the valve is actuated, the carriage and gate are slid towards the vacuum port until the carriage reaches the end of the valve body. This positions the gate concentric to the port. Continued pressure on the carriage causes a set of stainless-steel balls, riding in a decreasing depth groove between the carriage and the gate, to exert outward pressure on the gate. This outward force pushes the gate into its closed position. A leak-tight seal is obtained as the outward pressure forces the gate’s O-ring seal to be pressed against the valve body’s sealing surface. It is common for these valves to achieve an extended life of 300,000 cycles before service is needed. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Position Indicators: All of our UltraLock series of pneumatic gate valves include a visible external position indicator - the white ring conveniently mounted below the pneumatic piston. Pneumatic UltraLock gate valves also include open and closed reed sensor switches which are mounted on the valve’s pneumatic cylinder. These switches can be used to activate indicator lights or used to control a more complex or automated vacuum protection system. Solenoid Valves: We offer solenoid kits for pneumatic valves in voltages of 12 VDC, 24 VDC, and 120 VAC. Solenoid kits are sold separately and include the solenoid valve, mounting bracket with fasteners used to attach the solenoid to the gate valve’s bonnet flange, and flexible 1/4” OD airlines to connect between the push-to-connect fittings on the gate valve’s pneumatic cylinder and the solenoid valve. Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.
Condition: New
Part Number: P1013067
Price: KD721.54
Ideal Vacuum UltraLock High Vacuum HV Pneumatic Gate Valve ISO-F DN 100 Flange, Ball Groove Locking, Viton Seals, 304 Stainless Steel. ISO-100 Bolt Down Flange with M8 x 1.25 Threads. Includes Reed Switch Position Indicators. These Ideal Vacuum UltraLock™ pneumatically operated gate valves have an ISO-F DN 100 vacuum flange with M8 x 1.25 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. Our new UltraLock series of premium pneumatically operated vacuum gate valves are built using an innovative ball-and-groove locking mechanism which keeps the valve locked closed during loss of power or air pressure, while reducing wear and extending operating life. These UltraLock gate valves have a typical life of 300,000 cycles before needing service and are made with corrosion resistant 304 stainless-steel gates and valve bodies. An easily visible external position indicator and position sensor switches are standard on all pneumatic UltraLock gate valves.UltraLock Locking Mechanism: Our UltraLock high vacuum gate valves employ an ingenious ball-and-groove mechanism to lock the valve. Inside the valve body is a rolling carriage with lubricated ball bearings on which the gate is attached. When the valve is actuated, the carriage and gate are slid towards the vacuum port until the carriage reaches the end of the valve body. This positions the gate concentric to the port. Continued pressure on the carriage causes a set of stainless-steel balls, riding in a decreasing depth groove between the carriage and the gate, to exert outward pressure on the gate. This outward force pushes the gate into its closed position. A leak-tight seal is obtained as the outward pressure forces the gate’s O-ring seal to be pressed against the valve body’s sealing surface. It is common for these valves to achieve an extended life of 300,000 cycles before service is needed. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Position Indicators: All of our UltraLock series of pneumatic gate valves include a visible external position indicator - the white ring conveniently mounted below the pneumatic piston. Pneumatic UltraLock gate valves also include open and closed reed sensor switches which are mounted on the valve’s pneumatic cylinder. These switches can be used to activate indicator lights or used to control a more complex or automated vacuum protection system. Solenoid Valves: We offer solenoid kits for pneumatic valves in voltages of 12 VDC, 24 VDC, and 120 VAC. Solenoid kits are sold separately and include the solenoid valve, mounting bracket with fasteners used to attach the solenoid to the gate valve’s bonnet flange, and flexible 1/4” OD airlines to connect between the push-to-connect fittings on the gate valve’s pneumatic cylinder and the solenoid valve. Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.
Condition: New
Part Number: P1013045
Price: KD835.45
Ideal Vacuum UltraLock High Vacuum HV Pneumatic Gate Valve ISO-F DN 160 Flange, Ball Groove Locking, Viton Seals, 304 Stainless Steel. ISO-160 Bolt Down Flange with M10 x 1.50 Threads. Includes Reed Switch Position Indicators. These Ideal Vacuum UltraLock™ pneumatically operated gate valves have an ISO-F DN 160 vacuum flange with M10 x 1.50 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. Our new UltraLock series of premium pneumatically operated vacuum gate valves are built using an innovative ball-and-groove locking mechanism which keeps the valve locked closed during loss of power or air pressure, while reducing wear and extending operating life. These UltraLock gate valves have a typical life of 300,000 cycles before needing service and are made with corrosion resistant 304 stainless-steel gates and valve bodies. An easily visible external position indicator and position sensor switches are standard on all pneumatic UltraLock gate valves.UltraLock Locking Mechanism: Our UltraLock high vacuum gate valves employ an ingenious ball-and-groove mechanism to lock the valve. Inside the valve body is a rolling carriage with lubricated ball bearings on which the gate is attached. When the valve is actuated, the carriage and gate are slid towards the vacuum port until the carriage reaches the end of the valve body. This positions the gate concentric to the port. Continued pressure on the carriage causes a set of stainless-steel balls, riding in a decreasing depth groove between the carriage and the gate, to exert outward pressure on the gate. This outward force pushes the gate into its closed position. A leak-tight seal is obtained as the outward pressure forces the gate’s O-ring seal to be pressed against the valve body’s sealing surface. It is common for these valves to achieve an extended life of 300,000 cycles before service is needed. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Position Indicators: All of our UltraLock series of pneumatic gate valves include a visible external position indicator - the white ring conveniently mounted below the pneumatic piston. Pneumatic UltraLock gate valves also include open and closed reed sensor switches which are mounted on the valve’s pneumatic cylinder. These switches can be used to activate indicator lights or used to control a more complex or automated vacuum protection system. Solenoid Valves: We offer solenoid kits for pneumatic valves in voltages of 12 VDC, 24 VDC, and 120 VAC. Solenoid kits are sold separately and include the solenoid valve, mounting bracket with fasteners used to attach the solenoid to the gate valve’s bonnet flange, and flexible 1/4” OD airlines to connect between the push-to-connect fittings on the gate valve’s pneumatic cylinder and the solenoid valve. Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.
Condition: New
Part Number: P1013071
Price: KD1,170.54
Ideal Vacuum UltraLock High Vacuum HV Pneumatic Gate Valve ISO-F DN 200 Flange, Ball Groove Locking, Viton Seals, 304 Stainless Steel. ISO-200 Bolt Down Flange with M10 x 1.50 Threads. Includes Reed Switch Position Indicators. These Ideal Vacuum UltraLock™ pneumatically operated gate valves have an ISO-F DN 200 vacuum flange with M10 x 1.50 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. Our new UltraLock series of premium pneumatically operated vacuum gate valves are built using an innovative ball-and-groove locking mechanism which keeps the valve locked closed during loss of power or air pressure, while reducing wear and extending operating life. These UltraLock gate valves have a typical life of 300,000 cycles before needing service and are made with corrosion resistant 304 stainless-steel gates and valve bodies. An easily visible external position indicator and position sensor switches are standard on all pneumatic UltraLock gate valves.UltraLock Locking Mechanism: Our UltraLock high vacuum gate valves employ an ingenious ball-and-groove mechanism to lock the valve. Inside the valve body is a rolling carriage with lubricated ball bearings on which the gate is attached. When the valve is actuated, the carriage and gate are slid towards the vacuum port until the carriage reaches the end of the valve body. This positions the gate concentric to the port. Continued pressure on the carriage causes a set of stainless-steel balls, riding in a decreasing depth groove between the carriage and the gate, to exert outward pressure on the gate. This outward force pushes the gate into its closed position. A leak-tight seal is obtained as the outward pressure forces the gate’s O-ring seal to be pressed against the valve body’s sealing surface. It is common for these valves to achieve an extended life of 300,000 cycles before service is needed. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Position Indicators: All of our UltraLock series of pneumatic gate valves include a visible external position indicator - the white ring conveniently mounted below the pneumatic piston. Pneumatic UltraLock gate valves also include open and closed reed sensor switches which are mounted on the valve’s pneumatic cylinder. These switches can be used to activate indicator lights or used to control a more complex or automated vacuum protection system. Solenoid Valves: We offer solenoid kits for pneumatic valves in voltages of 12 VDC, 24 VDC, and 120 VAC. Solenoid kits are sold separately and include the solenoid valve, mounting bracket with fasteners used to attach the solenoid to the gate valve’s bonnet flange, and flexible 1/4” OD airlines to connect between the push-to-connect fittings on the gate valve’s pneumatic cylinder and the solenoid valve. Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.
Condition: New
Part Number: P1013073
Price: KD1,399.20
Ideal Vacuum UltraLock High Vacuum HV Pneumatic Gate Valve ISO-F DN 250 Flange, Ball Groove Locking, Viton Seals, 304 Stainless Steel. ISO-250 Bolt Down Flange with M10 x 1.50 Threads. Includes Reed Switch Position Indicators. These Ideal Vacuum UltraLock™ pneumatically operated gate valves have an ISO-F DN 250 vacuum flange with M10 x 1.50 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. Our new UltraLock series of premium pneumatically operated vacuum gate valves are built using an innovative ball-and-groove locking mechanism which keeps the valve locked closed during loss of power or air pressure, while reducing wear and extending operating life. These UltraLock gate valves have a typical life of 50,000 cycles before needing service and are made with corrosion resistant 304 stainless-steel gates and valve bodies. An easily visible external position indicator and position sensor switches are standard on all pneumatic UltraLock gate valves.UltraLock Locking Mechanism: Our UltraLock high vacuum gate valves employ an ingenious ball-and-groove mechanism to lock the valve. Inside the valve body is a rolling carriage with lubricated ball bearings on which the gate is attached. When the valve is actuated, the carriage and gate are slid towards the vacuum port until the carriage reaches the end of the valve body. This positions the gate concentric to the port. Continued pressure on the carriage causes a set of stainless-steel balls, riding in a decreasing depth groove between the carriage and the gate, to exert outward pressure on the gate. This outward force pushes the gate into its closed position. A leak-tight seal is obtained as the outward pressure forces the gate’s O-ring seal to be pressed against the valve body’s sealing surface. It is common for these valves to achieve an extended life of 50,000 cycles before service is needed. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Position Indicators: All of our UltraLock series of pneumatic gate valves include a visible external position indicator - the white ring conveniently mounted below the pneumatic piston. Pneumatic UltraLock gate valves also include open and closed reed sensor switches which are mounted on the valve’s pneumatic cylinder. These switches can be used to activate indicator lights or used to control a more complex or automated vacuum protection system. Solenoid Valves: We offer solenoid kits for pneumatic valves in voltages of 12 VDC, 24 VDC, and 120 VAC. Solenoid kits are sold separately and include the solenoid valve, mounting bracket with fasteners used to attach the solenoid to the gate valve’s bonnet flange, and flexible 1/4” OD airlines to connect between the push-to-connect fittings on the gate valve’s pneumatic cylinder and the solenoid valve. Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.
Condition: New
Part Number: P1013076
Price: KD2,099.87
Ideal Vacuum UltraLock High Vacuum HV Pneumatic Gate Valve ISO-F DN 320 Flange, Linkage Locking, Viton Seals, 304 Stainless Steel. ISO-320 Bolt Down Flange with M12 x 1.75 Threads and Internal Limit Switches These Ideal Vacuum UltraLock™ pneumatically operated gate valves have an ISO-F DN 320 vacuum flange with M12 x 1.75 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. These large pneumatically operated vacuum gate valves are built using a lever linkage locking mechanism which keeps the valve locked closed during loss of power or air pressure. These HV gate valves have a typical life of 50,000 cycles before needing service and are made with corrosion resistant 304 stainless-steel gates and valve bodies. These valves have built-in limit switches which can be used to activate indicator lights or used to control a more complex or automated vacuum protection system. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Solenoid Valves: We offer solenoid kits for our pneumatic valves in voltages of 12 VDC, 24 VDC, and 120 VAC. Solenoid kits are sold separately and include the solenoid valve, mounting bracket with fasteners used to attach the solenoid to the gate valve’s bonnet flange, and flexible 1/4” OD airlines to connect between the push-to-connect fittings on the gate valve’s pneumatic cylinder and the solenoid valve. Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.
Condition: New
Part Number: P1013077
Price: KD2,812.32
Ideal Vacuum UltraLock High Vacuum HV Pneumatic Gate Valve ISO-F DN 400 Flange, Linkage Locking, Viton Seals, 304 Stainless Steel. ISO-400 Bolt Down Flange with M12 x 1.75 Threads. Includes Reed Switch Position Indicators These Ideal Vacuum UltraLock™ pneumatically operated gate valves have an ISO-F DN 400 vacuum flange with M12 x 1.75 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. These large pneumatically operated vacuum gate valves are built using a lever linkage locking mechanism which keeps the valve locked closed during loss of power or air pressure. These HV gate valves have a typical life of 20,000 cycles before needing service and are made with corrosion resistant 304 stainless-steel valve bodies and aluminum gates to reduce weight. These pneumatic gate valves include open and closed reed sensor switches which are mounted on the valve’s pneumatic cylinder. These switches can be used to activate indicator lights or used to control a more complex or automated vacuum protection system. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Solenoid Valves: We offer solenoid kits for our pneumatic valves in voltages of 12 VDC, 24 VDC, and 120 VAC. Solenoid kits are sold separately and include the solenoid valve, mounting bracket with fasteners used to attach the solenoid to the gate valve’s bonnet flange, and flexible 1/4” OD airlines to connect between the push-to-connect fittings on the gate valve’s pneumatic cylinder and the solenoid valve. Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.
Condition: New
Part Number: P1013069
Price: KD4,958.45
Ideal Vacuum UltraLock High Vacuum HV Pneumatic Gate Valve ISO-F DN 500 Flange, Linkage Locking, Viton Seals, 304 Stainless Steel. ISO-500 Bolt Down Flange with M12 x 1.75 Threads. Includes Reed Switch Position Indicators These Ideal Vacuum UltraLock™ pneumatically operated gate valves have an ISO-F DN 500 vacuum flange with M12 x 1.75 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. These large pneumatically operated vacuum gate valves are built using a lever linkage locking mechanism which keeps the valve locked closed during loss of power or air pressure. These HV gate valves have a typical life of 20,000 cycles before needing service and are made with corrosion resistant 304 stainless-steel valve bodies and aluminum gates to reduce weight. These pneumatic gate valves include open and closed reed sensor switches which are mounted on the valve’s pneumatic cylinder. These switches can be used to activate indicator lights or used to control a more complex or automated vacuum protection system. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Solenoid Valves: We offer solenoid kits for our pneumatic valves in voltages of 12 VDC, 24 VDC, and 120 VAC. Solenoid kits are sold separately and include the solenoid valve, mounting bracket with fasteners used to attach the solenoid to the gate valve’s bonnet flange, and flexible 1/4” OD airlines to connect between the push-to-connect fittings on the gate valve’s pneumatic cylinder and the solenoid valve. Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.
Condition: New
Part Number: P1012807
Price: KD6,198.45
Ideal Vacuum UltraLock High Vacuum HV Pneumatic Gate Valve ISO-F DN 630 Flange, Linkage Locking, Ball Type, Viton Seals, 304 Stainless Steel. ISO-630 Bolt Down Flange with M12 x 1.75 Threads. Includes Reed Switch Position Indicators These Ideal Vacuum UltraLock™ pneumatically operated gate valves have an ISO-F DN 630 vacuum flange with M12 x 1.75 blind-tapped holes. They are rated for high vacuum (HV) and follow vacuum technology standards as described in DIN 28404 and ISO 1609. These large pneumatically operated vacuum gate valves are built using a lever linkage locking mechanism which keeps the valve locked closed during loss of power or air pressure. These HV gate valves have a typical life of 20,000 cycles before needing service and are made with corrosion resistant 304 stainless-steel valve bodies and aluminum gates to reduce weight. These pneumatic gate valves include open and closed reed sensor switches which are mounted on the valve’s pneumatic cylinder. These switches can be used to activate indicator lights or used to control a more complex or automated vacuum protection system. UHV vs HV Versions: Our Conflat CF flanged gate valves are UHV rated. The bellows are welded to the bonnet plate, and oxygen-free, high-thermal conductivity (OFHC) copper sealing gaskets and flange knife-edges form the required metal-to-metal seal between the bonnet plate and valve body. Our Conflat UHV UltraLock valves have a low leak rate of < 3.75 x 10-10 Torr l/sec and are bakeable up to 200 °C with the gate open (150°C with the gate closed). Our KF and ISO-F flanged gate valves use Viton O-rings for the bellows and bonnet plate seals and are therefore limited to high-vacuum (HV) applications with ultimate pressures down to 3x10-8 Torr. KF and ISO-F series UltraLock valves have a leak rate of 1.5 x 10-9 Torr l/sec and are bakeable to 150 °C (with the valve open or closed). Solenoid Valves: We offer solenoid kits for our pneumatic valves in voltages of 12 VDC, 24 VDC, and 120 VAC. Solenoid kits are sold separately and include the solenoid valve, mounting bracket with fasteners used to attach the solenoid to the gate valve’s bonnet flange, and flexible 1/4” OD airlines to connect between the push-to-connect fittings on the gate valve’s pneumatic cylinder and the solenoid valve. Specifications: Our Ideal Vacuum UltraLock gate valves are designed for dependable High and Ultra- High Vacuum (UHV) applications and are often used in combination with cryo, turbo, and ion high vacuum pumps. Available sizes include Conflat CF 2.75, 4.5, 6, 8, 10, and 12 inch sizes; ISO-F DN -63, -100, -160, -200, -250, -320, -400, -500, and -630 sizes; and quick flanged sizes KF-40 and KF-50. Please see the downloads for more information.
Condition: New
Part Number: P1013405
Price: KD10,850.00
Solenoid Kit for UtraLock Pneumatic Gate Valve, 110-120 VAC, Includes Mounting Hardware. This solenoid kit is for use with an Ideal Vacuum ULTRALockTM or HVA pneumatically operated gate valve. The solenoid operates the gate valve’s pneumatic piston. All fittings and connections must be leak-tight to ensure proper operation. These 110-120 VAC solenoid kits include an AVS-5111-120A, 4-way, direct-acting solenoid valve, and everything else needed to operate an UltraLock or HVA pneumatic gate valve including air line tubing push-to-connect fittings. For faster actuation of larger gate valves, larger tubing and different push-to-connect fittings may be used. Kit Components: AVS-5111-120A 4-way solenoid valve. Mounting bracket for use with Ideal Vacuum UltraLock or HVA pneumatic gate valves. All necessary mounting screws and hardware for use with UltraLock pneumatic gate valves. Five (5) 4 mm OD tubing push-to-connect to 1/8" male universal pipe thread adapters. Two (2) exhaust mufflers. 6’ length of 1/4" OD flexible polyurethane tubing. Solenoid Valve Features: 24 VDC, 3.5 VA. 20-115 PSIG working input pressure. 215 PSIG max input pressure. 80 PSIG required for most pneumatic gate valves. Five (5) 1/8" NPSF ports: A: Normally open outlet to P. Exhausted to A when energized. B: Normally exhausted outlet to R. Open to P when energized. P: Inlet. R: Normally closed. Exhaust from A when energized. S: Normally exhaust from B. Closed when energized. Locking manual override button. Din style wiring connector with LED indicator. Buna rubber seals. When properly connected, if there is an interruption to the solenoid’s electrical power, the attached gate valve immediately closes and remains in the closed position until power is restored. The solenoid valve has a red manual override button. When properly connected, pushing the overide button forces the gate valve to open. When the override button is released the gate valve closes. The override button may be locked in the pressed position using a flat head screw driver and rotating the button 90°. Rotating the button back to its original position will allow it to spring back to the unpressed position. Installation Instructions: Mount the solenoid on to the gate valve bonnet using the included mounting bracket and screws. When no tapped holes are present, the solenoid must be mounted remotely. Attach air line tubing between solenoid port B and the gate valve’s port which opens the gate valve when pressurized (the port closest to the bonnet). Attach air line tubing between solenoid port A and the other gate valve port which closes the gate valve when pressurized (the port at the top of the pneumatic cylinder). Optionally connect solenoid ports R and S to house exhaust. Attach solenoid port P to (user supplied) house air at 80 psi. Apply 80 PSI air pressure to the solenoid valve and verify that the gate valve closes and remains closed. If the gate valve opens and remains open, switch the tubes to solenoid outlets A and B. Press the manual overide switch and verify that the gate valve opens and remains open while the switch is pressed. Release the manual overide switch and verify that the gate valve closes again. With no electrical power applied, the solenoid will automatically be in the closed, locked position . When electrical power is applied to the solenoid, the gate valve will open.
Condition: New
Part Number: P1013464
Price: KD74.09
Solenoid Kit for UtraLock Pneumatic Gate Valve, 24 VDC, Includes Mounting Hardware. This solenoid kit is for use with an Ideal Vacuum ULTRALockTM or HVA pneumatically operated gate valve. The solenoid operates the gate valve’s pneumatic piston. All fittings and connections must be leak-tight to ensure proper operation. These 24 VDC solenoid kits include an AVS-5111-24D, 4-way, direct-acting solenoid valve, and everything else needed to operate an UltraLock or HVA pneumatic gate valve including air line tubing push-to-connect fittings. For faster actuation of larger gate valves, larger tubing and different push-to-connect fittings may be used. Kit Components: AVS-5111-24D 4-way solenoid valve. Mounting bracket for use with Ideal Vacuum UltraLock or HVA pneumatic gate valves. All necessary mounting screws and hardware for use with UltraLock pneumatic gate valves. Five (5) 4 mm OD tubing push-to-connect to 1/8" male universal pipe thread adapters. Two (2) exhaust mufflers. 6’ length of 1/4" OD flexible polyurethane tubing. Solenoid Valve Features: 24 VDC, 2.5 W. 20-115 PSIG working input pressure. 215 PSIG max input pressure. 80 PSIG required for most pneumatic gate valves. Five (5) 1/8" NPSF ports: A: Normally open outlet to P. Exhausted to A when energized. B: Normally exhausted outlet to R. Open to P when energized. P: Inlet. R: Normally closed. Exhaust from A when energized. S: Normally exhaust from B. Closed when energized. Locking manual override button. Din style wiring connector with LED indicator. Buna rubber seals. When properly connected, if there is an interruption to the solenoid’s electrical power, the attached gate valve immediately closes and remains in the closed position until power is restored. The solenoid valve has a red manual override button. When properly connected, pushing the overide button forces the gate valve to open. When the override button is released the gate valve closes. The override button may be locked in the pressed position using a flat head screw driver and rotating the button 90°. Rotating the button back to its original position will allow it to spring back to the unpressed position. Installation Instructions: Mount the solenoid on to the gate valve bonnet using the included mounting bracket and screws. When no tapped holes are present, the solenoid must be mounted remotely. Attach air line tubing between solenoid port B and the gate valve’s port which opens the gate valve when pressurized (the port closest to the bonnet). Attach air line tubing between solenoid port A and the other gate valve port which closes the gate valve when pressurized (the port at the top of the pneumatic cylinder). Optionally connect solenoid ports R and S to house exhaust. Attach solenoid port P to (user supplied) house air at 80 psi. Apply 80 PSI air pressure to the solenoid valve and verify that the gate valve closes and remains closed. If the gate valve opens and remains open, switch the tubes to solenoid outlets A and B. Press the manual overide switch and verify that the gate valve opens and remains open while the switch is pressed. Release the manual overide switch and verify that the gate valve closes again. With no electrical power applied, the solenoid will automatically be in the closed, locked position . When electrical power is applied to the solenoid, the gate valve will open.
Condition: New
Part Number: P1013465
Price: KD74.09
Bolt Kit for ISO-F DN 63 Gate Valve with Threaded Hole Flange, Includes 4 Silver Plated M8 x 1.25 x 20 mm Long Bolts and 4 Stainless Steel Washers. These bolt kits consist of 4 hex head, silver plated M8 x 1.25 bolts, 20 mm long, and 4 stainless steel flat washers. They are properly sized for connecting ISO-F 63 hole through flanges and fittings to the threaded holes in ISO 63 gate valves. Gate valves have standardized flange, thread, and thread depth specifications. These bolt kits are correct for connecting any gate valve of this flange type and size to an unthreaded flange of the same size, no matter the manufacturer. A centering ring with O-ring seal is required and sold separately (part number P101761). The length of the bolts in this kit are specially measured so they tighten ISO-F to ISO-F flanges fully but don’t bottom out in the blind threaded holes of the gate valve’s flange. The bolts are silver plated to prevent galling or seizing of the bolts and to make them easier to loosen, especially if they have been heated to bakeout temperatures. If the gate valve is to be connected/adapted to an ISO-K type flange, such as might be found on a turbo pump, single claw clamps with longer bolts and centering rings are required.
Condition: New
Part Number: P1013154
Price: KD4.09
Bolt Kit for ISO-F DN 80 Gate Valve with Threaded Hole Flange, Includes 8 Silver Plated M8 x 1.25 x 20 mm Long Bolts and 8 Stainless Steel Washers. 1.25 mm Pitch. These bolt kits consist of 8 hex head, silver plated M8 x 1.25 bolts, 20 mm long, and 8 stainless steel flat washers. They are properly sized for connecting ISO-F 80 hole through flanges and fittings to the threaded holes in ISO 80 gate valves. Gate valves have standardized flange, thread, and thread depth specifications. These bolt kits are correct for connecting any gate valve of this flange type and size to an unthreaded flange of the same size, no matter the manufacturer. A centering ring with O-ring seal is required and sold separately. The length of the bolts in this kit are specially measured so they tighten ISO-F to ISO-F flanges fully but don’t bottom out in the blind threaded holes of the gate valve’s flange. The bolts are silver plated to prevent galling or seizing of the bolts and to make them easier to loosen, especially if they have been heated to bakeout temperatures. If the gate valve is to be connected/adapted to an ISO-K type flange, such as might be found on a turbo pump, single claw clamps with longer bolts and centering rings are required. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange sizes of NW-80. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-80, NW-100, Vacuum Flanges, Silver-Plated, Quantity of 8ISO-LF Flange Size: NW-80Quantity: 8 bolts include washersCommon Dimensions: Bolt Size M8 x 20 x 1.25mm Pitch
Condition: New
Part Number: P1013180
Price: KD5.30
Bolt Kit for ISO-F DN 100 Gate Valve with Threaded Hole Flange, Includes 8 Silver Plated M8 x 1.25 x 20 mm Long Bolts and 8 Stainless Steel Washers, 1.25 mm Pitch. These bolt kits consist of 8 hex head, silver plated M8 x 1.25 bolts, 20 mm long, and 8 stainless steel flat washers. They are properly sized for connecting ISO-F 100 hole through flanges and fittings to the threaded holes in ISO 100 gate valves. Gate valves have standardized flange, thread, and thread depth specifications. These bolt kits are correct for connecting any gate valve of this flange type and size to an unthreaded flange of the same size, no matter the manufacturer. A centering ring with O-ring seal is required and sold separately. The length of the bolts in this kit are specially measured so they tighten ISO-F to ISO-F flanges fully but don’t bottom out in the blind threaded holes of the gate valve’s flange. The bolts are silver plated to prevent galling or seizing of the bolts and to make them easier to loosen, especially if they have been heated to bakeout temperatures. If the gate valve is to be connected/adapted to an ISO-K type flange, such as might be found on a turbo pump, single claw clamps with longer bolts and centering rings are required. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange sizes of NW-100. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-80, NW-100, Vacuum Flanges, Silver-Plated, Quantity of 8ISO-LF Flange Size: NW-100Quantity: 8 bolts include washersCommon Dimensions: Bolt Size M8 x 20 x 1.25mm Pitch
Condition: New
Part Number: P1013155
Price: KD5.30
ISO-F DN 160 Bolt Set, for Ideal Vacuum UltraLock Gate Valves Tapped Holes, Metric M10 x 25 mm Long Bolts, 1.50 mm Pitch, Silver-Plated, Quantity of 8 washers included. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange sizes of NW-160. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-160, Vacuum Flanges, Silver-Plated, Quantity of 8ISO-LF Flange Size: NW-160Quantity: 8 bolts include washersCommon Dimensions: Bolt Size M10 x 30 x 1.50mm Pitch
Condition: New
Part Number: P1013156
Price: KD6.06
Bolt Kit for ISO-F DN 200 Tapped Holes Gate Valve Flange, Threaded Holes, Includes Twelve M10 x 1.50 x 25 mm Long Silver Plated Bolts and Twelve Washers, 1.50 mm Pitch. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange sizes of NW-200. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-200, Vacuum Flanges, Silver-Plated, Quantity of 12ISO-LF Flange Size: NW-200Quantity: 12 bolts include washersCommon Dimensions: Bolt Size M10 x 30 x 1.50mm Pitch
Condition: New
Part Number: P1013157
Price: KD8.16
ISO-F DN 250 Bolt Set, for Ideal Vacuum UltraLock Gate Valves Tapped Holes, Metric M10 x 35 mm Long Bolts, 1.50 mm Pitch, Silver-Plated, Quantity of 12 bolts washers included. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange size NW-250. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-250, Vacuum Flanges, Silver-Plated, Quantity of 12ISO-LF Flange Size: NW-250Quantity: 12 bolts include washersCommon Dimensions: Bolt Size M10 x 40 x 1.50mm Pitch
Condition: New
Part Number: P1013158
Price: KD9.48
Bolt Kit for ISO-F DN 320 Bolt Gate Valve with Tapped Hole Flange, Includes 12 Silver Plated M12 x 1.75 x 35 mm Long Bolts and 12 Stainless Steel Washers, 1.75 mm Pitch. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange size NW-320. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-320, Vacuum Flanges, Silver-Plated, Quantity of 12ISO-LF Flange Size: NW-320Quantity: 12 bolts include washersCommon Dimensions: Bolt Size M12 x 40 x 1.75mm Pitch
Condition: New
Part Number: P1013159
Price: KD11.80
ISO-F DN 400 Bolt Set, for Ideal Vacuum UltraLock Gate Valves Tapped Holes, Metric M12 x 50 mm Long Bolts, 1.75 mm Pitch, Silver-Plated, Quantity of 16 bolts washers included. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange size NW-400. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-400, Vacuum Flanges, Silver-Plated, Quantity of 16ISO-LF Flange Size: NW-400Quantity: 16 bolts include washersCommon Dimensions: Bolt Size M12 x 50 x 1.75mm Pitch
Condition: New
Part Number: P1013160
Price: KD13.13
ISO-F DN 500 Bolt Set, for Ideal Vacuum UltraLock Gate Valves Tapped Holes, Metric M12 x 50 mm Long Bolts, 1.75 mm Pitch, Silver-Plated, Quantity of 16 bolts washers included. These bolts are for tapped threaded hole flanges and follow ISO-LF standards for flange size NW-500. ISO flanged vacuum fittings are commonly used to build process vacuum plumbing and systems for industrial applications. The fittings are quick to assemble using double claw clamps and a centering ring (please see top right figure - click to enlarge). The Viton® centering ring contains a rubber/elastomeric o-ring. The ISO standard sizes for large flanges are NW-63, NW-80, NW-100, NW-160, NW-200, NW-250, NW-320, NW-400, NW-500, NW-630. These vacuum fittings are made of corrosive resistant stainless steel.Bolts, for Tapped Threaded Hole NW-500, Vacuum Flanges, Silver-Plated, Quantity of 16ISO-LF Flange Size: NW-500Quantity: 16 bolts include washersCommon Dimensions: Bolt Size M12 x 50 x 1.75mm Pitch
Condition: New
Part Number: P1013161
Price: KD14.79
ISO 63 Centering Ring Aluminum with Viton® O-Ring, NW-63 Vacuum Flange Size, Typically Used With 2.5 Inch O.D. (63.50 mm) Tubing. These ISO DN 63 centering rings are made of aluminum with durable Viton® (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 63 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material.ISO DN 63 Centering Ring, for Sealing of NW-63 Vacuum Flanges, Aluminum with Viton® O-Ring (FPM) ISO-LF Flange Size: NW-63Common Dimensions:A = 2.75" (70.00mm) B = 0.15" (3.90mm)
Condition: New
Part Number: P101766
Price: KD16.31
ISO 100 Centering Ring Aluminum with Viton® O-Ring, NW-100 Vacuum Flange Size, Typically Used with 4 Inch O.D. (101.6 mm) Tubing These ISO DN 100 centering rings are made of aluminum with durable Viton® (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 100 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material. ISO DN 100 Centering Ring, for Sealing of NW-100 Vacuum Flanges, Aluminum with Viton® O-Ring (FPM) ISO-LF Flange Size: NW-100 Common Dimensions:A = 4.01" (102.00 mm) B = 0.15" (3.9 mm)
Condition: New
Part Number: P101768
Price: KD18.28
ISO 160 Centering Ring Aluminum with Viton® O-Ring, NW-160 Vacuum Flange Size, Typically Used with 6 Inch O.D. (152.4 mm) Tubing These ISO DN 160 centering rings are made of aluminum with durable Viton® (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 160 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material. ISO DN 160 Centering Ring, for Sealing of NW-160 Vacuum Flanges, Aluminum with Viton® O-Ring (FPM) ISO-LF Flange Size: NW-160 Common Dimensions:A = 6.02" (153.00 mm) B = 0.15" (3.9 mm)
Condition: New
Part Number: P101769
Price: KD23.06
ISO 200 Centering Ring Aluminum with Viton® O-Ring, NW-200 Vacuum Flange Size, Typically Used with 8 Inch O.D. (203.2 mm) Tubing These ISO DN 200 centering rings are made of aluminum with durable Viton® (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 200 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material. ISO DN 200 Centering Ring, for Sealing of NW-200 Vacuum Flanges, Aluminum with Viton® O-Ring (FPM) ISO-LF Flange Size: NW-200 Common Dimensions:A = 8.38" (213.00 mm) B = 0.15" (3.9 mm)
Condition: New
Part Number: P101770
Price: KD30.54
ISO 250 Centering Ring, NW-250 Vacuum Flange Size, Aluminum with Viton® O-Ring, Typically Used with 10 Inch O.D. (254 mm) Tubing. These ISO DN 250 centering rings are made of aluminum with durable Viton® (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 250 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material. ISO DN 250 Centering Ring, for Sealing of NW-250 Vacuum Flanges, Aluminum with Viton® O-Ring (FPM) ISO-LF Flange Size: NW-250 Common Dimensions:A = 10.28" (261.00 mm) B = 0.15" (3.90mm)
Condition: New
Part Number: P1012741
Price: KD35.99
ISO 320 Centering Ring, NW-320 Vacuum Flange Size, Aluminum with Viton® O-Ring, Typically Used With 12 Inch O.D. (304.8 mm) Tubing. These ISO DN 320 centering rings are made of aluminum with durable Viton® (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 320 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material. ISO DN 320 Centering Ring, For Sealing of NW-320 Vacuum Flanges, Aluminum with Viton® O-Ring (FPM) ISO-LF Flange Size: NW-320 Common Dimensions:A = 12.52" (318mm) B = 0.22" (5.60mm)
Condition: New
Part Number: P1012742
Price: KD55.67
ISO 400 Centering Ring, NW-400 Vacuum Flange Size, Aluminum with Viton® O-Ring, Typically Used With 16 Inch O.D. (406.4 mm) Tubing. These ISO DN 400 centering rings are made of aluminum with durable Viton® (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 400 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material. ISO DN 400 Centering Ring, For Sealing of NW-400 Vacuum Flanges, Aluminum with Viton® O-Ring (FPM) ISO-LF Flange Size: NW-400 Common Dimensions:A = 15.75" (400mm) B = 0.22" (5.60mm)
Condition: New
Part Number: P1012743
Price: KD71.47
ISO 500 Centering Ring, NW-500 Vacuum Flange Size, Aluminum with Viton O-Ring, Typically Used With 20 Inch O.D. (508 mm) Tubing. These ISO DN 500 centering rings are made of aluminum with durable viton (FPM) rubber O-rings and are used to seal both ISO-K and ISO-F vacuum flanges. These centering rings follow vacuum technology standards as described in DIN 28404 and ISO 1609. The centering ring which contains a rubber elastomeric O-ring forms the vacuum seal between the two mating ISO-K or ISO-F flange faces. ISO-K fittings are quick to assemble using claw clamps (please see figure - click to enlarge) and can be connected together in any orientation. The claw clamp hooks into a ridged groove in the back side of the ISO-K flange. ISO-F fixed flange vacuum fittings are different and have a bolt circle where bolts align the two flanges. These ISO 500 centering rings are commonly used to build process vacuum plumbing and systems for industrial standard and high vacuum applications. The ISO standard sizes for large LF flanges are ISO-F and ISO-K DN 63, 80, 100, 160, 200, 250, 320, 400, 500, 630, 800, 1000. These vacuum fittings are made with inner and outer rings of Aluminum 6082 with FPM rubber O-ring material. ISO DN 500 Centering Ring, For Sealing of NW-500 Vacuum Flanges, Aluminum with Viton O-Ring (FPM) ISO-LF Flange Size: NW-500 Common Dimensions:A = 19.72" (501mm) B = 0.22" (5.60mm)
Condition: New
Part Number: P1012744
Price: KD87.72