MKS 622D 1 Torr Baratron Absolute Capacitance Manometer, Vacuum Fitting 1/2 in Tube OD, Terminal Block Connector, MKS Part Number: 622D01TAE . The MKS 622D unheated absolute Baratron® capacitance manometers are the latest analog, capacitance-based, high-performance vacuum and pressure transducers. They require ±15 VDC input voltage and provide a high-level 0-10 VDC analog output signal that is linear with pressure. This analog output can be interfaced with an MKS PDR2000 pressure controller, an MKS power supply/display instrument, or any instrument that meets these requirements. Changes in pressure/vacuum are determined by measuring the change in capacitance between the sensor’s diaphragm and an adjacent electrode disk. This capacitance change is converted to a useable output by patented signalconditioning electronic circuits. The radially-tensioned Inconel® diaphragm in the sensor provides very fast response (<20 msec in many cases), low hysteresis, excellent repeatability, very high resolution (to 0.001% of Full Scale), exceptionally high corrosion resistance, and double-walled welded construction for operator safety. The sensor itself can withstand repeated exposures to 45 psia (3.1 bar) without permanent degradation or shifting, allowing it to operate in virtually any process system. The MKS 622D Baratron capacitance manometers operate at ambient conditions. They are available in full scale pressure/vacuum ranges from 0.1 to 1000 Torr and are suited for many industrial, electronic, and research applications. These listing is for an MKS Type 622D capacitance manometers having a terminal block connector, a 1 Torr full scale maximum vacuum pressure reading value, a 1/2 inch OD tube vacuum connection, and have MKS part number 622D01TAE . Compatible Controller and Cables: P102063 - Ideal Vacuum Cable For MKS PDR 2000 Power Supply and Digital Readout Cable 15-Pin Y Cable, Equivalent To CB2000S-1-M1 P102062 - MKS PDR 2000 Digital Power Supply and Digital Readout Capacitance Manometer Controller P1010127 - Ideal Vacuum Dual Capacitance Manometer Controller (DCM), Power Supply and Digital Pressure Readout Product Features: 0 to 10 VDC proportional analog output with terminal block connector Direct measurement of chamber total pressure independent of gas type or composition Long-term output stability for state-of-the-art process repeatability Inconel® and Incoloy® nickel alloy construction of basic sensor operates without damage in virtually any chemical environment High overpressure limit ensures reliability during system mishaps Specified in percent of reading for best accuracy and improved process yield

MKS 622D 2 Torr Baratron Absolute Capacitance Manometer, Vacuum Fitting 1/2 in Tube OD, Terminal Block Connector. PN: 622D02TAE . The MKS 622D unheated absolute Baratron® capacitance manometers are the latest analog, capacitance-based, high-performance vacuum and pressure transducers. They require ±15 VDC input voltage and provide a high-level 0-10 VDC analog output signal that is linear with pressure. This analog output can be interfaced with an MKS PDR2000 pressure controller, an MKS power supply/display instrument, or any instrument that meets these requirements. Changes in pressure/vacuum are determined by measuring the change in capacitance between the sensor’s diaphragm and an adjacent electrode disk. This capacitance change is converted to a useable output by patented signalconditioning electronic circuits. The radially-tensioned Inconel® diaphragm in the sensor provides very fast response (<20 msec in many cases), low hysteresis, excellent repeatability, very high resolution (to 0.001% of Full Scale), exceptionally high corrosion resistance, and double-walled welded construction for operator safety. The sensor itself can withstand repeated exposures to 45 psia (3.1 bar) without permanent degradation or shifting, allowing it to operate in virtually any process system. The MKS 622D Baratron capacitance manometers operate at ambient conditions. They are available in full scale pressure/vacuum ranges from 0.1 to 1000 Torr and are suited for many industrial, electronic, and research applications. These listing is for an MKS Type 622D capacitance manometers having a terminal block connector, a 2 Torr full scale maximum vacuum pressure reading value, a 1/2 inch OD tube vacuum connection, and have MKS part number 622D02TAE . Compatible Controller and Cables: P102063 - Ideal Vacuum Cable For MKS PDR 2000 Power Supply and Digital Readout Cable 15-Pin Y Cable, Equivalent To CB2000S-1-M1 P102062 - MKS PDR 2000 Digital Power Supply and Digital Readout Capacitance Manometer Controller P1010127 - Ideal Vacuum Dual Capacitance Manometer Controller (DCM), Power Supply and Digital Pressure Readout Product Features: 0 to 10 VDC proportional analog output with terminal block connector Direct measurement of chamber total pressure independent of gas type or composition Long-term output stability for state-of-the-art process repeatability Inconel® and Incoloy® nickel alloy construction of basic sensor operates without damage in virtually any chemical environment High overpressure limit ensures reliability during system mishaps Specified in percent of reading for best accuracy and improved process yield

MKS 622D 10 Torr Baratron Absolute Capacitance Manometer, Vacuum Fitting 1/2 in Tube OD, Terminal Block Connector, MKS Part Number: 622D11TAE. The MKS 622D unheated absolute Baratron® capacitance manometers are the latest analog, capacitance-based, high-performance vacuum and pressure transducers. They require ±15 VDC input voltage and provide a high-level 0-10 VDC analog output signal that is linear with pressure. This analog output can be interfaced with an MKS PDR2000 pressure controller, an MKS power supply/display instrument, or any instrument that meets these requirements. Changes in pressure/vacuum are determined by measuring the change in capacitance between the sensor’s diaphragm and an adjacent electrode disk. This capacitance change is converted to a useable output by patented signalconditioning electronic circuits. The radially-tensioned Inconel® diaphragm in the sensor provides very fast response (<20 msec in many cases), low hysteresis, excellent repeatability, very high resolution (to 0.001% of Full Scale), exceptionally high corrosion resistance, and double-walled welded construction for operator safety. The sensor itself can withstand repeated exposures to 45 psia (3.1 bar) without permanent degradation or shifting, allowing it to operate in virtually any process system. The MKS 622D Baratron capacitance manometers operate at ambient conditions. They are available in full scale pressure/vacuum ranges from 0.1 to 1000 Torr and are suited for many industrial, electronic, and research applications. These listing is for an MKS Type 622D capacitance manometers having a terminal block connector, a 10 Torr full scale maximum vacuum pressure reading value, a 1/2 inch OD tube vacuum connection, and have MKS part number 622D11TAE. Compatible Controller and Cables: P102063 - Ideal Vacuum Cable For MKS PDR 2000 Power Supply and Digital Readout Cable 15-Pin Y Cable, Equivalent To CB2000S-1-M1 P102062 - MKS PDR 2000 Digital Power Supply and Digital Readout Capacitance Manometer Controller P1010127 - Ideal Vacuum Dual Capacitance Manometer Controller (DCM), Power Supply and Digital Pressure Readout Product Features: 0 to 10 VDC proportional analog output with terminal block connector Direct measurement of chamber total pressure independent of gas type or composition Long-term output stability for state-of-the-art process repeatability Inconel® and Incoloy® nickel alloy construction of basic sensor operates without damage in virtually any chemical environment High overpressure limit ensures reliability during system mishaps Specified in percent of reading for best accuracy and improved process yield

MKS 622D 100 Torr Baratron Absolute Capacitance Manometer, Vacuum Fitting 1/2 in Tube OD, Terminal Block Connector, MKS Part Number: 622D11TAE. The MKS 622D unheated absolute Baratron® capacitance manometers are the latest analog, capacitance-based, high-performance vacuum and pressure transducers. They require ±15 VDC input voltage and provide a high-level 0-10 VDC analog output signal that is linear with pressure. This analog output can be interfaced with an MKS PDR2000 pressure controller, an MKS power supply/display instrument, or any instrument that meets these requirements. Changes in pressure/vacuum are determined by measuring the change in capacitance between the sensor’s diaphragm and an adjacent electrode disk. This capacitance change is converted to a useable output by patented signalconditioning electronic circuits. The radially-tensioned Inconel® diaphragm in the sensor provides very fast response (<20 msec in many cases), low hysteresis, excellent repeatability, very high resolution (to 0.001% of Full Scale), exceptionally high corrosion resistance, and double-walled welded construction for operator safety. The sensor itself can withstand repeated exposures to 45 psia (3.1 bar) without permanent degradation or shifting, allowing it to operate in virtually any process system. The MKS 622D Baratron capacitance manometers operate at ambient conditions. They are available in full scale pressure/vacuum ranges from 0.1 to 1000 Torr and are suited for many industrial, electronic, and research applications. These listing is for an MKS Type 622D capacitance manometers having a terminal block connector, a 100 Torr full scale maximum vacuum pressure reading value, a 1/2 inch OD tube vacuum connection, and have MKS part number 622D12TAE . Compatible Controller and Cables: P102063 - Ideal Vacuum Cable For MKS PDR 2000 Power Supply and Digital Readout Cable 15-Pin Y Cable, Equivalent To CB2000S-1-M1 P102062 - MKS PDR 2000 Digital Power Supply and Digital Readout Capacitance Manometer Controller P1010127 - Ideal Vacuum Dual Capacitance Manometer Controller (DCM), Power Supply and Digital Pressure Readout Product Features: 0 to 10 VDC proportional analog output with terminal block connector Direct measurement of chamber total pressure independent of gas type or composition Long-term output stability for state-of-the-art process repeatability Inconel® and Incoloy® nickel alloy construction of basic sensor operates without damage in virtually any chemical environment High overpressure limit ensures reliability during system mishaps Specified in percent of reading for best accuracy and improved process yield

MKS 622D 1,000 Torr Baratron Absolute Capacitance Manometer, Vacuum Fitting 1/2 in Tube OD, Terminal Block Connector, MKS Part Number: 622D13TAE . The MKS 622D unheated absolute Baratron® capacitance manometers are the latest analog, capacitance-based, high-performance vacuum and pressure transducers. They require ±15 VDC input voltage and provide a high-level 0-10 VDC analog output signal that is linear with pressure. This analog output can be interfaced with an MKS PDR2000 pressure controller, an MKS power supply/display instrument, or any instrument that meets these requirements. Changes in pressure/vacuum are determined by measuring the change in capacitance between the sensor’s diaphragm and an adjacent electrode disk. This capacitance change is converted to a useable output by patented signalconditioning electronic circuits. The radially-tensioned Inconel® diaphragm in the sensor provides very fast response (<20 msec in many cases), low hysteresis, excellent repeatability, very high resolution (to 0.001% of Full Scale), exceptionally high corrosion resistance, and double-walled welded construction for operator safety. The sensor itself can withstand repeated exposures to 45 psia (3.1 bar) without permanent degradation or shifting, allowing it to operate in virtually any process system. The MKS 622D Baratron capacitance manometers operate at ambient conditions. They are available in full scale pressure/vacuum ranges from 0.1 to 1000 Torr and are suited for many industrial, electronic, and research applications. These listing is for an MKS Type 622D capacitance manometers having a terminal block connector, a 1,000 Torr full scale maximum vacuum pressure reading value, a 1/2 inch OD tube vacuum connection, and have MKS part number 622D13TAE . Compatible Controller and Cables: P102063 - Ideal Vacuum Cable For MKS PDR 2000 Power Supply and Digital Readout Cable 15-Pin Y Cable, Equivalent To CB2000S-1-M1 P102062 - MKS PDR 2000 Digital Power Supply and Digital Readout Capacitance Manometer Controller P1010127 - Ideal Vacuum Dual Capacitance Manometer Controller (DCM), Power Supply and Digital Pressure Readout Product Features: 0 to 10 VDC proportional analog output with terminal block connector Direct measurement of chamber total pressure independent of gas type or composition Long-term output stability for state-of-the-art process repeatability Inconel® and Incoloy® nickel alloy construction of basic sensor operates without damage in virtually any chemical environment High overpressure limit ensures reliability during system mishaps Specified in percent of reading for best accuracy and improved process yield

IVP Cable For XGC-520 and MKS PDR2000 Controller, Dual Sensor Y Cable, DB9M to Two DB15F, Equivalent To CB2000S-1-M1. This is a dual sensor cable for the Ideal Vacuum XGC-520 Dual Capacitance Manometer Gauge Controller (P1010127) and the MKS PDR2000 (P102062). It connects the controller to up to two Baratron sensors with DB15 pinouts. This Y splitter cable has a DB9 male on one end which connects to the controller, and two DB15 female connectors on the other. This cable is manufactured by Ideal Vacuum and is a direct replacement for MKS part number CB2000S-1-M1. Ths cable is compatible with Baratron models127, 128, 626, 627, 628 or 722 series sensors with 15 pin male connectors. These cables are 10 feet long.

IVP Dual Capacitance Manometer Gauge Controller with USB for MKS Baratron Gauges, LCD Readout and Two Setpoints. The Ideal Vacuum Products (IVP) XGC-520 Dual Capacitance Manometer Gauge Controller is an inexpensive solution for pressure readout of up to two Capacitance Diaphragm Gauges. This IVP exclusive controller provides enhanced accuracy with intelligently designed features for simple user control and easy system integration. The controller is designed to interface with the popular 626D, 627H, and 722C series of Baratron® capacitance diaphragm gauges from MKS and can read full scale absolute vacuum/pressure ranges from 20 mTorr (2 x 10-4 Torr) to as much as 10,000 Torr (1x104 Torr). Because these gauges measure absolute pressure, they are gas type and composition independent. Lookup tables and conversion factors are not required. The unit has two analog output relays, each of which can be assigned to either of the two gauge channels and programmed to energize when a setpoint is reached. This flexibility allows the user to easily set up automated tasks, such as valve activation or energizing a turbomolecular pump when an appropriate backing pump pressure is achieved. The Dual Capacitance Manometer Gauge Controller is conveniently housed in a compact 1/8-DIN extruded aluminum enclosure for benchtop or rack panel mounting. The brilliant, blue LCD display is easy to read and displays vital system and controller information at a glance. The intuitive front panel membrane switch interface allows the user to access and adjust all parameters quickly. Remote communication and control is achieved by RS-232 serial terminal software. Connection is made via the rear-mounted DB15 or USB-B connectors. A variety of sensor and serial cables are available. The controller has a built-in universal power supply which accepts an input of 100-240 VAC, 50/60Hz. Included is a 2 meter long (6 ft.) 115 VAC input power cord with US plug 5-15P to C13 Connector. Features: Controls up to two (2) capacitive diaphragm sensor gauges (CDG) Interfaces with all popular MKS 626D, 627H, and 722C series Baratron sensor gauges, heated or unheated, with full scale measurement ranges from 20 mTorr to 10,000 Torr Gas type and composition independent - no need for lookup tables and conversion factors Compact 1/8-DIN enclosure for benchtop or rack panel mounting Brilliant Blue LCD readout display Intuitive interface makes setting parameters quick and easy Two setpoint output relays for automated control of other equipment User selectable pressure units for each gauge (Torr, mTorr, mBar, and Pa) Serial communication for remote control through DB9 and USB-B ports Available Cables and Adapters: P102063 Sensor cable, connects two gauges to DCM,10 ft., DB9 -M to two DB15-F P102061 Sensor cable, connects two gauges to DCM, 10 ft. DB9-M to two DB9-F P1011364 Serial cable, connects remote computer to DCM, 10 ft., DB15-M to DB9-F P1012796 USB cable, connects remote computer to DCM, 10 ft. USB-A to USB-B P1012800 DB15-M to terminal block breakout for splitting out relays and RS232 cables Please download the user manual for complete information.

MKS PDR2000 Power Supply and Digital Readout Capacitance Manometer Controller. MKS Part Number: PDR2000AO. The MKS PDR2000 power supply and digital readout capacitance manometer controller provides up to 750mA to operate two Baratron pressure transducers. The MKS PDR 200 can display one channel at a time on a 4-1/2 digital meter readout. The MKS PDR 2000 has two configurable relay set points, an RS-232 output, and a 0 to 10 VDC linear output for each transducer. Cables for the MKS PDR 2000 are available but sold separately.

SWIFT-SEAL KF-16 to 1/2 in. I.D. Compression Port, Quick Coupling Adapter, KF16, NW-16, 304 Stainless Steel This adapter converts a KF-16 flanged fitting to a 0.5 in. compression port. Compression ports are typically used to make quick connections to tubes and half nipples, commonly found on gauges, instruments, and gas supply lines. SWIFT-SEAL KF adapters create a leak-proof seal when the knurled ring is tightened, allowing the uniquely shaped inner ring to both wedge and compress the O-ring circumferentially around the tube. An inner circlip can be re-located to any of the 3 indexed slots (or removed altogether), to make fast, repeatable tube insertions into the adapter; required for repeated, quick changeouts. All components can be easily dismantled for routine service. SWIFT-SEAL adapters are made of 304 Stainless Steel and anodized aluminum. Dimension Details: 1 = KF-16 2 = 0.52 in. (13.2 mm) 3 = 0.79 in. (19.9 mm) 4 = 1.04 in. (26.3 mm) 5 = 1.29 in. (32.7 mm)

SWIFT-SEAL KF-25 to 1/2 in. I.D. Compression Port, Quick Coupling Adapter, KF25, NW-25, 304 Stainless Steel This adapter converts a KF-25 flanged fitting to a 0.5 in. compression port. Compression ports are typically used to make quick connections to tubes and half nipples, commonly found on gauges, instruments, and gas supply lines. SWIFT-SEAL KF adapters create a leak-proof seal when the knurled ring is tightened, allowing the uniquely tapered inner ring to both wedge and compress the O-ring circumferentially around the tube. An inner circlip can be re-located to any of the 3 indexed slots (or removed altogether), to make fast, repeatable tube insertions into the adapter; required for repeated, precise, and quick changeouts. All components can be easily dismantled for routine service. SWIFT-SEAL adapters are made of 304 Stainless Steel and anodized aluminum. Dimension Details: 1 = KF25 2 = 0.52 in. (13.2 mm) 3 = 0.76 in. (19.2 mm) 4 = 1.00 in. (25.6 mm) 5 = 1.26 in. (31.9 mm)

SWIFT-SEAL KF-40 to 1/2 in. I.D. Compression Port, Quick Coupling Adapter, KF40, NW-16, 304 Stainless Steel This adapter converts a KF-40 flanged fitting to a 0.5 in. compression port. Compression ports are typically used to make quick connections to tubes and half nipples, commonly found on gauges, instruments, and gas supply lines. "SWIFT-SEAL" KF adapters create a leak-proof seal when the knurled ring is tightened, allowing the uniquely shaped inner ring to both wedge and compress the O-ring circumferentially around the tube. An inner circlip can be re-located to any of the 3 indexed slots (or removed altogether), to make fast, repeatable tube insertions into the adapter; required for repeated, quick changeouts. All components can be easily dismantled for routine service. SWIFT-SEAL adapters are made of 304 Stainless Steel and anodized aluminum. Dimension Details: 1 = KF-402 = 0.52 in. (13.2 mm)3 = 0.85 in. (21.7 mm)4 = 1.10 in. (28.0 mm)5 = 1.35 in. (34.5 mm)

SWIFT-SEAL KF-50 to 1/2 in. I.D. Compression Port, Quick Coupling Adapter, KF50, NW-50, 304 Stainless Steel This adapter converts a KF-50 flanged fitting to a 0.5 in. compression port. Compression ports are typically used to make quick connections to tubes and half nipples, commonly found on gauges, instruments, and gas supply lines. SWIFT-SEAL KF adapters create a leak-proof seal when the knurled ring is tightened, allowing the uniquely shaped inner ring to both wedge and compress the O-ring circumferentially around the tube. An inner circlip can be re-located to any of the 3 indexed slots (or removed altogether), to make fast, repeatable tube insertions into the adapter; required for repeated, quick changeouts. All components can be easily dismantled for routine service. SWIFT-SEAL adapters are made of 304 Stainless Steel and anodized aluminum. Dimension Details: 1 = KF-16 2 = 0.52 in. (13.2 mm) 3 = 0.74 in. (18.9 mm) 4 = 0.99 in. (25.2 mm) 5 = 1.24 in. (31.6 mm)

Adapter KF-16 to 1/2 in. Swagelok, ISO-KF Flange Size NW-16, Stainless Steel These adapters connect KF-16 to 1/2 in Swagelok®. The flange size follows ISO-KF standards and is NW-16. They are commonly used to make connections between ISO-KF fittings and Swagelok fittings. The ISO-KF flanges are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Stainless Steel. Adapter KF-16 to 1/2 in. Swagelok, ISO-KF Flange Size NW-16, Stainless Steel Flange Size: ISO-KF NW-16 Tube Size: 1/2 in. O.D. Common Dimensions: A = 1.96 Swagelok-TM Swagelok Company

Adapter KF-25 to 1/2 in. Swagelok, ISO-KF Flange Size NW-25, Stainless Steel These adapters connect KF-25 to 1/2 in Swagelok®. The flange size follows ISO-KF standards and is NW-25. They are commonly used to make connections between ISO-KF fittings and Swagelok fittings. The ISO-KF flanges are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Stainless Steel. Adapter KF-25 to 1/2 in. Swagelok, ISO-KF Flange Size NW-25, Stainless Steel Flange Size: ISO-KF NW-25 Tube Size: 1/2 in. O.D. Common Dimensions: A = 2.02 Swagelok-TM Swagelok Company

Adapter KF-40 to 1/2 in. Swagelok, ISO-KF Flange Size NW-40, Stainless Steel These adapters connect KF-40 to 1/2 in Swagelok®. The flange size follows ISO-KF standards and is NW-40. They are commonly used to make connections between ISO-KF fittings and Swagelok fittings. The ISO-KF flanges are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Stainless Steel. Adapter KF-40 to 1/2 in. Swagelok, ISO-KF Flange Size NW-40, Stainless Steel Flange Size: ISO-KF NW-40 Tube Size: 1/2 in. O.D. Common Dimensions: A = 1.97 Swagelok-TM Swagelok Company

Adapter KF-50 to 1/2 in. Swagelok, ISO-KF Flange Size NW-50, Stainless Steel These adapters connect KF-50 to 1/2 in Swagelok®. The flange size follows ISO-KF standards and is NW-50. They are commonly used to make connections between ISO-KF fittings and Swagelok fittings. The ISO-KF flanges are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Stainless Steel. Adapter KF-50 to 1/2 in. Swagelok, ISO-KF Flange Size NW-50, Stainless Steel Flange Size: ISO-KF NW-50 Tube Size: 1/2 in. O.D. Common Dimensions: A = 1.65 Swagelok-TM Swagelok Company

Hinge Clamp KF-10, KF-16 Vacuum Fittings, ISO-KF Flange Size NW-10, NW-16, AluminumThese KF-10, KF-16 Hinge Clamp vacuum fittings follow ISO-KF standards and have a flange size of NW-10, NW-16. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Aluminum.KF-10, KF-16 Hinge ClampISO-KF Flange Size: NW-16Common Dimensions: A=2.45" (62.30mm)B=1.61" (41mm)C=0.649" (16.5mm)

Hinge Clamp KF-25 Vacuum Fittings, ISO-KF Flange Size NW-25, AluminumThese KF-25 Hinge Clamp vacuum fittings follow ISO-KF standards and have a flange size of NW-25. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Aluminum.KF-25 Hinge ClampISO-KF Flange Size: NW-25Common Dimensions:A=2.85" (72.40mm)B=2.12" (54mm)C=0.649" (16.50mm)

Hinge Clamp KF-40 Vacuum Fittings, ISO-KF Flange Size NW-40, AluminumThese KF-40 Hinge Clamp vacuum fittings follow ISO-KF standards and have a flange size of NW-40. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Aluminum.KF-40 Hinge ClampISO-KF Flange Size: NW-40Common Dimensions:A=3.53" (89.70mm)B=2.71" (69mm)C=0.649" (16.50mm)

Hinge Clamp KF-50 Vacuum Fittings, ISO-KF Flange Size NW-50, AluminumThese KF-50 Hinge Clamp vacuum fittings follow ISO-KF standards and have a flange size of NW-50. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Aluminum.KF-50 Hinge ClampISO-KF Flange Size: NW-50Common Dimensions:A=4.49 (114.00mm)B=3.54 (90mm)C=0.846 (21.50mm)

Centering Ring KF-16 Vacuum Fittings, ISO-KF Flange Size NW-16, Stainless Steel & Viton® O-RingThese KF-16 Centering Ring vacuum fittings follow ISO-KF standards and have a flange size of NW-16. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of corrosive resistant stainless steel with Viton® O-Ring. Viton® is well known for its excellent resistance to heat (400°F/200°C) and to aggressive fuels and chemicals. Viton® is a registered trademark of DuPont Performance Elastomers.KF-16 Centering Ring with Viton® O-RingISO-KF Flange Size: NW-16

Centering Ring KF-25 Vacuum Fittings, ISO-KF Flange Size NW-25, Stainless Steel & Viton® O-ringThese KF-25 Centering Ring vacuum fittings follow ISO-KF standards and have a flange size of NW-25. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of corrosive resistant stainless steel with Viton® O-Ring. Viton® is well known for its excellent resistance to heat (400°F/200°C) and to aggressive fuels and chemicals. Viton® is a registered trademark of DuPont Performance Elastomers.KF-25 Centering Ring with Viton® O-RingISO-KF Flange Size: NW-25

Centering Ring KF-40 Vacuum Fittings, ISO-KF Flange Size NW-40, Stainless Steel & Viton® O-ringThese KF-40 Centering Ring vacuum fittings follow ISO-KF standards and have a flange size of NW-40. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of corrosive resistant stainless steel with Viton® O-Ring. Viton® is well known for its excellent resistance to heat (400°F/200°C) and to aggressive fuels and chemicals. Viton® is a registered trademark of DuPont Performance Elastomers.KF-40 Centering Ring with Viton® O-RingISO-KF Flange Size: NW-40

Centering Ring KF-50 Vacuum Fittings, ISO-KF Flange Size NW-50, Stainless Steel & Viton®These KF-50 Centering Ring vacuum fittings follow ISO-KF standards and have a flange size of NW-50. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of corrosive resistant stainless steel with Viton® O-Ring. Viton® is well known for its excellent resistance to heat (400°F/200°C) and to aggressive fuels and chemicals. Viton® is a registered trademark of DuPont Performance Elastomers.KF-50 Centering Ring with Viton® O-RingISO-KF Flange Size: NW-50

Conflat Flange (CF) 2-3/4 inch connected to Swagelok 1/2 inch, Stainless Steel Fittings These Conflat to Swagelok® vacuum fittings have a flange size of ConFlat (CF) 2-3/4 inch connected to Swagelok 1/2 inch. ConFlat (CF) flanges are used for ultra-high vacuum applications. These fittings use a copper gasket and knife-edge flanges to achieve the high vacuum seal and can operate down to 10-13 torr (10-11 Pa) and can be heated to 450 °C for bake-out. North American flange sizes are given by flange outer diameter in inches: 1-1/3 (mini conflat), 2¾, 4½, 6, 8, 10, 12, 13¼, 14 and 16½. In Europe and Asia, sizes are given by tube inner diameter in millimeters: DN16, DN40, DN63, DN100, DN160, DN200, DN250. These vacuum fittings are made of corrosion resistant stainless steel. Conflat Flange (CF) 2-3/4 inch to Swagelok 1/2 inch, Stainless Steel Fittings CF Flange Size: CF 2-3/4 inch to Swagelok 1/2 inch Common Dimensions: Tube Size 1/2 inch Swagelok-TM Swagelok Company

Conflat Flange (CFF) Copper Gaskets CF Size 2-3/4" These conflat copper conflat gaskets fit a conflat flange size of 2-3/4 inches. ConFlat (CF) flanges are used for ultra-high vacuum applications. These fittings use a copper gasket and knife-edge flanges to achieve the high vacuum seal and can operate down to 10-13 torr (10-11 Pa) and can be heated to 450°C for bake-out. North American flange sizes are given by flange outer diameter in inches: 1-1/3 ("mini conflat"), 2¾, 4½, 6, 8, 10, 12, 13¼, 14 and 16½ , in Europe and Asia, sizes are given by tube inner diameter in millimeters: DN16, DN40, DN63, DN100, DN160, DN200, DN250. These vacuum fittings are made of corrosive resistant stainless steel. Conflat Flange (CF) Copper Gaskets CF Size 2-3/4" - 1 eachCF Flange Size: CF 2-3/4 inch Common Dimensions: Flange Outer Diameter (OD) 2-3/4", Gasket Outer Diameter (OD) 1.895", Gasket Inner Diameter (ID) 1.451"

Bolt Kit For 2.75 (2-3/4)Inch Conflat Clear Bolt Hole Flanges, Silver-Plated 12 Point Bolts With Platenuts.These bolt kits contain silver-plated 12-point head bolts, platenuts, and washers to fasten clearance hole 2.75 (2-3/4) inch CF Conflat flanged fittings. These confalt flages can be pumped down to 10-13 torr (10-11 Pa) and can be heated to 450 °C for bake-out. North American flange sizes are given by flange outer diameter in inches: 1-1/3 ("mini conflat"), 2-1/8, 2-3/4, 4-1/2, 4-5/8, 6, 6-3/4, 8, 10, 12, 13-1/4, 14 and 16-1/2. In Europe and Asia, sizes are given by tube inner diameter in millimeters: DN16, DN40, DN63, DN100, DN160, DN200, DN250. These are complete kits, with bolts, washers, and platenuts to fasten one conflat clearance hole 2.75 (2-3/4) inch flange connection.Complete Kit - 2.75 (2-3/4) inch Conflat Clearance Bolt Hole Fasteners: QTY 6, Silver-Plated 1/4 x 1.25 Inch Long 12-Point Bolts QTY 6, Washers QTY 3, Platenut