Keyword Part Number:
Pfeiffer Vacuum HiScroll 6 Oil-Free Dry Scroll Vacuum Pump, 100-240 VAC, 3.6 cfm, KF-25 Inlet & Outlet. Pfeiffer Part Number: PD S10 000. This Pfeiffer HiScroll 6 dry scroll roughing/backing pump has a pumping speed of 3.6 cfm (6.1 m3/hr), and an ultimate vacuum of 1.5 x 10-2 Torr (2 x 10-2 mbar). It has KF-25 (NW25) inlet and outlet ports. Input of 100-240 VAC, 50/60 Hz, single phase power is required and and the pump has a standard C14 input power connector. The HiScroll 6 pump draws 4A@120VAC (2A@240 VAC) and is extremely quiet at 48 dB(A). This HiScroll pump has internal motor protection and an integrated two-stage gas ballast which allows for pumping of condensable vapours including water, solvents, dilute acids and bases. Maximum dry air or inert gas ballast pressure is 21.7 psi (1500 hPa). The pump has an onboard inverter controller which allows the pump to be controlled either manually with easy-to-use push buttons, or remotely via RS485 when connected to a Pfeiffer DCU or OmniControl controller, or a user supplied software interface. The pump controller has a standby mode and when active reduces the speed of the pump to 50% of full speed to save wear and tear on tip seals and to increase bearing service life. This Pfeiffer HiScroll 6 dry scroll pump has part number PD S10 000. About the Pfeiffer HiScroll Series of Dry Scroll Vacuum Pumps: The Pfeiffer HiScroll dry scroll vacuum pump series consists of three dry and hermetically sealed scroll pumps with a nominal pumping speed of 6 - 20 m3/ h. The pumps are especially characterized by their high performance when evacuating against atmosphere due to their unique features. Their powerful IPM synchronous motors achieve an efficiency that is up to 15% higher than that of conventional drives. The pumps are also characterized by their very compact design and extremely quiet and low-vibration operation. Therefore, they are ideal for use in quiet working environments, for example on mass spectrometers, research & development institutes or leak detection systems. The Pfeiffer HiScroll dry scroll vacuum pumps can be easily connected to other Pfeiffer Vacuum products (such as turbopumps or display and control units) as well as to a higher-level external controller, via RS-485 or ProfiNet. The interface enables RPM regulation, situation-specific control of the fan and monitoring of the pump performance. This helps to minimize wear and noise emissions, and ensures longer maintenance intervals. The integrated two-stage gas ballast and safety valve ensure process-specific and safe operation. The proven quality of Pfeiffer Vacuum components guarantees pump longevity. Easy maintenance enables short service times and the efficient motor helps to reduce electricity costs. We carry all the replacement parts and rebuild kits to maintain and keep your Pfeiffer HiScroll vacuum pump in peak operating condition. Please see the operating instruction manual in the downloads.
Condition: New
Part Number: P1011104
Price: NZ$9,155.78
Regular Price: NZ$10,771.50
Pfeiffer Vacuum HiScroll 6 Oil-Free Dry Scroll Vacuum Pump with Pressure Sensor, 100-240 VAC, 3.6 cfm, KF-25 Inlet & Outlet. Pfeiffer Part Number: PD S10 010. This Pfeiffer HiScroll 6 dry scroll roughing/backing pump with pressure sensor has a pumping speed of 3.6 cfm (6.1 m3/hr), and an ultimate vacuum of 1.5 x 10-2 Torr (2 x 10-2 mbar). It has KF-25 (NW25) inlet and outlet ports. Input of 100-240 VAC, 50/60 Hz, single phase power is required and and the pump has a standard C14 input power connector. The HiScroll 6 pump draws 4A@120VAC (2A@240 VAC) and is extremely quiet at 48 dB(A). This HiScroll pump has internal motor protection and an integrated two-stage gas ballast which allows for pumping of condensable vapours including water, solvents, dilute acids and bases. Maximum dry air or inert gas ballast pressure is 21.7 psi (1500 hPa). This Hiscroll 6 pump with the pressure sensor option provides pressure regulation by varying the speed of the pump so that a target pressure is achieved. Pressure regulation operation is effective in the range between final pressure and 22.5 Torr (30 hPa). The pump has an onboard inverter controller which allows the pump to be controlled either manually with easy-to-use push buttons, or remotely via RS485 when connected to a Pfeiffer DCU or OmniControl controller, or a user supplied software interface. The pump controller has a standby mode and when active reduces the speed of the pump to 50% of full speed to save wear and tear on tip seals and to increase bearing service life. This Pfeiffer HiScroll 6 dry scroll pump with pressure sensor has part number PD S10 010. About the Pfeiffer HiScroll Series of Dry Scroll Vacuum Pumps: The Pfeiffer HiScroll dry scroll vacuum pump series consists of three dry and hermetically sealed scroll pumps with a nominal pumping speed of 6 - 20 m3/ h. The pumps are especially characterized by their high performance when evacuating against atmosphere due to their unique features. Their powerful IPM synchronous motors achieve an efficiency that is up to 15% higher than that of conventional drives. The pumps are also characterized by their very compact design and extremely quiet and low-vibration operation. Therefore, they are ideal for use in quiet working environments, for example on mass spectrometers, research & development institutes or leak detection systems. The Pfeiffer HiScroll dry scroll vacuum pumps can be easily connected to other Pfeiffer Vacuum products (such as turbopumps or display and control units) as well as to a higher-level external controller, via RS-485 or ProfiNet. The interface enables RPM regulation, situation-specific control of the fan and monitoring of the pump performance. This helps to minimize wear and noise emissions, and ensures longer maintenance intervals. The integrated two-stage gas ballast and safety valve ensure process-specific and safe operation. The proven quality of Pfeiffer Vacuum components guarantees pump longevity. Easy maintenance enables short service times and the efficient motor helps to reduce electricity costs. We carry all the replacement parts and rebuild kits to maintain and keep your Pfeiffer HiScroll vacuum pump in peak operating condition. Please see the operating instruction manual in the downloads.
Condition: New
Part Number: P1011105
Price: NZ$14,081.17
Regular Price: NZ$16,566.08
Pfeiffer Vacuum HiScroll 12 Oil-Free Dry Scroll Vacuum Pump, 100-240 VAC, 7.1 cfm, KF-25 Inlet & Outlet. Pfeiffer Part Number: PD S20 000. This Pfeiffer HiScroll 12 dry scroll roughing/backing pump has a pumping speed of 7.1 cfm (12.1 m3/hr), and an ultimate vacuum of 6.75 x 10-3 Torr (9 x 10-3 mbar). It has KF-25 (NW25) inlet and outlet ports. Input of 100-240 VAC, 50/60 Hz, single phase power is required and and the pump has a standard C14 input power connector. The HiScroll 12 pump draws 8A@120VAC (4A@240 VAC) and is extremely quiet at 47 dB(A). This HiScroll pump has internal motor protection and an integrated two-stage gas ballast which allows for pumping of condensable vapours including water, solvents, dilute acids and bases. Maximum dry air or inert gas ballast pressure is 21.7 psi (1500 hPa). The pump has an onboard inverter controller which allows the pump to be controlled either manually with easy-to-use push buttons, or remotely via RS485 when connected to a Pfeiffer DCU or OmniControl controller, or a user supplied software interface. The pump controller has a standby mode and when active reduces the speed of the pump to 50% of full speed to save wear and tear on tip seals and to increase bearing service life. This Pfeiffer HiScroll 12 dry scroll pump has part number PD S20 000. About the Pfeiffer HiScroll Series of Dry Scroll Vacuum Pumps: The Pfeiffer HiScroll dry scroll vacuum pump series consists of three dry and hermetically sealed scroll pumps with a nominal pumping speed of 6 - 20 m3/ h. The pumps are especially characterized by their high performance when evacuating against atmosphere due to their unique features. Their powerful IPM synchronous motors achieve an efficiency that is up to 15% higher than that of conventional drives. The pumps are also characterized by their very compact design and extremely quiet and low-vibration operation. Therefore, they are ideal for use in quiet working environments, for example on mass spectrometers, research & development institutes or leak detection systems. The Pfeiffer HiScroll dry scroll vacuum pumps can be easily connected to other Pfeiffer Vacuum products (such as turbopumps or display and control units) as well as to a higher-level external controller, via RS-485 or ProfiNet. The interface enables RPM regulation, situation-specific control of the fan and monitoring of the pump performance. This helps to minimize wear and noise emissions, and ensures longer maintenance intervals. The integrated two-stage gas ballast and safety valve ensure process-specific and safe operation. The proven quality of Pfeiffer Vacuum components guarantees pump longevity. Easy maintenance enables short service times and the efficient motor helps to reduce electricity costs. We carry all the replacement parts and rebuild kits to maintain and keep your Pfeiffer HiScroll vacuum pump in peak operating condition. Please see the operating instruction manual in the downloads.
Condition: New
Part Number: P1011106
Price: NZ$26,663.64
Pfeiffer Vacuum HiScroll 12 Oil-Free Dry Scroll Vacuum Pump with Pressure Sensor, 100-240 VAC, 7.1 cfm, KF-25 Inlet & Outlet. Pfeiffer Part Number: PD S20 010. This Pfeiffer HiScroll 12 dry scroll roughing/backing pump with pressure sensor has a pumping speed of 7.1 cfm (12.1 m3/hr), and an ultimate vacuum of 6.75 x 10-3 Torr (9 x 10-3 mbar). It has KF-25 (NW25) inlet and outlet ports. Input of 100-240 VAC, 50/60 Hz, single phase power is required and and the pump has a standard C14 input power connector. The HiScroll 12 pump draws 8A@120VAC (4A@240 VAC) and is extremely quiet at 47 dB(A). This HiScroll pump has internal motor protection and an integrated two-stage gas ballast which allows for pumping of condensable vapours including water, solvents, dilute acids and bases. Maximum dry air or inert gas ballast pressure is 21.7 psi (1500 hPa). This Hiscroll 12 pump with the pressure sensor option provides pressure regulation by varying the speed of the pump so that a target pressure is achieved. Pressure regulation operation is effective in the range between final pressure and 22.5 Torr (30 hPa). The pump has an onboard inverter controller which allows the pump to be controlled either manually with easy-to-use push buttons, or remotely via RS485 when connected to a Pfeiffer DCU or OmniControl controller, or a user supplied software interface. The pump controller has a standby mode and when active reduces the speed of the pump to 50% of full speed to save wear and tear on tip seals and to increase bearing service life. This Pfeiffer HiScroll 12 dry scroll pump has part number PD S20 010. About the Pfeiffer HiScroll Series of Dry Scroll Vacuum Pumps: The Pfeiffer HiScroll dry scroll vacuum pump series consists of three dry and hermetically sealed scroll pumps with a nominal pumping speed of 6 - 20 m3/ h. The pumps are especially characterized by their high performance when evacuating against atmosphere due to their unique features. Their powerful IPM synchronous motors achieve an efficiency that is up to 15% higher than that of conventional drives. The pumps are also characterized by their very compact design and extremely quiet and low-vibration operation. Therefore, they are ideal for use in quiet working environments, for example on mass spectrometers, research & development institutes or leak detection systems. The Pfeiffer HiScroll dry scroll vacuum pumps can be easily connected to other Pfeiffer Vacuum products (such as turbopumps or display and control units) as well as to a higher-level external controller, via RS-485 or ProfiNet. The interface enables RPM regulation, situation-specific control of the fan and monitoring of the pump performance. This helps to minimize wear and noise emissions, and ensures longer maintenance intervals. The integrated two-stage gas ballast and safety valve ensure process-specific and safe operation. The proven quality of Pfeiffer Vacuum components guarantees pump longevity. Easy maintenance enables short service times and the efficient motor helps to reduce electricity costs. We carry all the replacement parts and rebuild kits to maintain and keep your Pfeiffer HiScroll vacuum pump in peak operating condition. Please see the operating instruction manual in the downloads.
Condition: New
Part Number: P1011107
Price: NZ$13,414.28
Regular Price: NZ$15,781.50
Pfeiffer Vacuum HiScroll 18 Oil-Free Dry Scroll Vacuum Pump, 100-240 VAC, 10.7 cfm, KF-25 Inlet & Outlet. Pfeiffer Part Number: PD S30 000. This Pfeiffer HiScroll 18 dry scroll roughing/backing pump has a pumping speed of 10.7 cfm (18.1 m3/hr), and an ultimate vacuum of 5.25 x 10-3 Torr (7 x 10-3 mbar). It has KF-25 (NW25) inlet and outlet ports. Input of 100-240 VAC, 50/60 Hz, single phase power is required and and the pump has a standard C14 input power connector. The HiScroll 18 pump draws 10A@120VAC (6A@240 VAC) and is extremely quiet at 47 dB(A). This HiScroll pump has internal motor protection and an integrated two-stage gas ballast which allows for pumping of condensable vapours including water, solvents, dilute acids and bases. Maximum dry air or inert gas ballast pressure is 21.7 psi (1500 hPa). The pump has an onboard inverter controller which allows the pump to be controlled either manually with easy-to-use push buttons, or remotely via RS485 when connected to a Pfeiffer DCU or OmniControl controller, or a user supplied software interface. The pump controller has a standby mode and when active reduces the speed of the pump to 50% of full speed to save wear and tear on tip seals and to increase bearing service life. This Pfeiffer HiScroll 18 dry scroll pump has part number PD S30 000. About the Pfeiffer HiScroll Series of Dry Scroll Vacuum Pumps: The Pfeiffer HiScroll dry scroll vacuum pump series consists of three dry and hermetically sealed scroll pumps with a nominal pumping speed of 6 - 20 m3/ h. The pumps are especially characterized by their high performance when evacuating against atmosphere due to their unique features. Their powerful IPM synchronous motors achieve an efficiency that is up to 15% higher than that of conventional drives. The pumps are also characterized by their very compact design and extremely quiet and low-vibration operation. Therefore, they are ideal for use in quiet working environments, for example on mass spectrometers, research & development institutes or leak detection systems. The Pfeiffer HiScroll dry scroll vacuum pumps can be easily connected to other Pfeiffer Vacuum products (such as turbopumps or display and control units) as well as to a higher-level external controller, via RS-485 or ProfiNet. The interface enables RPM regulation, situation-specific control of the fan and monitoring of the pump performance. This helps to minimize wear and noise emissions, and ensures longer maintenance intervals. The integrated two-stage gas ballast and safety valve ensure process-specific and safe operation. The proven quality of Pfeiffer Vacuum components guarantees pump longevity. Easy maintenance enables short service times and the efficient motor helps to reduce electricity costs. We carry all the replacement parts and rebuild kits to maintain and keep your Pfeiffer HiScroll vacuum pump in peak operating condition. Please see the operating instruction manual in the downloads.
Condition: New
Part Number: P1011108
Price: NZ$13,928.48
Regular Price: NZ$16,386.46
Pfeiffer Vacuum HiScroll 18 Oil-Free Dry Scroll Vacuum Pump with Pressure Sensor, 100-240 VAC, 10.7 cfm, KF-25 Inlet & Outlet. Pfeiffer Part Number: PD S30 010. This Pfeiffer HiScroll 18 dry scroll roughing/backing pump with pressure sensor has a pumping speed of 10.7 cfm (18.1 m3/hr), and an ultimate vacuum of 5.25 x 10-3 Torr (7 x 10-3 mbar). It has KF-25 (NW25) inlet and outlet ports. Input of 100-240 VAC, 50/60 Hz, single phase power is required and and the pump has a standard C14 input power connector. The HiScroll 18 pump draws 10A@120VAC (6A@240 VAC) and is extremely quiet at 47 dB(A). This HiScroll pump has internal motor protection and an integrated two-stage gas ballast which allows for pumping of condensable vapours including water, solvents, dilute acids and bases. Maximum dry air or inert gas ballast pressure is 21.7 psi (1500 hPa). This Hiscroll 18 pump with the pressure sensor option provides pressure regulation by varying the speed of the pump so that a target pressure is achieved. Pressure regulation operation is effective in the range between final pressure and 22.5 Torr (30 hPa). The pump has an onboard inverter controller which allows the pump to be controlled either manually with easy-to-use push buttons, or remotely via RS485 when connected to a Pfeiffer DCU or OmniControl controller, or a user supplied software interface. The pump controller has a standby mode and when active reduces the speed of the pump to 50% of full speed to save wear and tear on tip seals and to increase bearing service life. This Pfeiffer HiScroll 18 dry scroll pump has part number PD S30 010. About the Pfeiffer HiScroll Series of Dry Scroll Vacuum Pumps: The Pfeiffer HiScroll dry scroll vacuum pump series consists of three dry and hermetically sealed scroll pumps with a nominal pumping speed of 6 - 20 m3/ h. The pumps are especially characterized by their high performance when evacuating against atmosphere due to their unique features. Their powerful IPM synchronous motors achieve an efficiency that is up to 15% higher than that of conventional drives. The pumps are also characterized by their very compact design and extremely quiet and low-vibration operation. Therefore, they are ideal for use in quiet working environments, for example on mass spectrometers, research & development institutes or leak detection systems. The Pfeiffer HiScroll dry scroll vacuum pumps can be easily connected to other Pfeiffer Vacuum products (such as turbopumps or display and control units) as well as to a higher-level external controller, via RS-485 or ProfiNet. The interface enables RPM regulation, situation-specific control of the fan and monitoring of the pump performance. This helps to minimize wear and noise emissions, and ensures longer maintenance intervals. The integrated two-stage gas ballast and safety valve ensure process-specific and safe operation. The proven quality of Pfeiffer Vacuum components guarantees pump longevity. Easy maintenance enables short service times and the efficient motor helps to reduce electricity costs. We carry all the replacement parts and rebuild kits to maintain and keep your Pfeiffer HiScroll vacuum pump in peak operating condition. Please see the operating instruction manual in the downloads.
Condition: New
Part Number: P1011109
Price: NZ$15,781.50
Pfeiffer Turbo OmniControl Controller and HiScroll Roughing Pump Power Supply Cord Mains Cable 115 VAC NEMA 5-15 to IEC C13, 3 m Long. This input power supply power cord (mains cable) is used on Pfeiffer OmniControl 200, 300, 400, and DCU 110 controllers, HiScroll dry scroll roughing/backing pumps, and with other Pfeiffer products. These power cords have a standard NEMA 5-15P 115 VAC plug one one end and an IEC320 C13 female socket connector on the other. This cable is 3 meters long (10 ft.) and has 18 gauge wire and 3 conductors (18/3).
Condition: New
Part Number: P103361
Price: NZ$99.05
Pfeiffer OEM Tip Seal Maintenance Kit for HiScroll 6 Scroll Vacuum Pumps. Pfeiffer P/N: PD E10 000-T This is a Pfeiffer OEM Tip Seal Maintenace Kit for Pfeiffer HiScroll 6 Scroll Vacuum Pumps. These are user friendly replaceable.
Condition: New
Part Number: P1011110
Price: NZ$1,587.90
Regular Price: NZ$1,671.67
Pfeiffer OEM Tip Seal Maintenance Kit for HiScroll 12 or HiScroll 18 Scroll Vacuum Pumps. Pfeiffer P/N: PD E20 000-T This is a Pfeiffer OEM Tip Seal Maintenace Kit for Pfeiffer HiScroll 12 or HiScroll 18 Scroll Vacuum Pumps. These are user friendly replaceable.
Condition: New
Part Number: P1011111
Price: NZ$1,587.90
Regular Price: NZ$1,671.67
Pfeiffer Screw Cap for Gas Ballast on 6-12-18 HiScroll Vacuum Pumps. Pfeiffer P/N: PD 100 067 This is a Pfeiffer Screw Cap for the Gas Ballast on 6-12-18 HiScroll Pfeiffer Vacuum Pumps.
Condition: New
Part Number: P1011112
Price: NZ$318.62
Pfeiffer HPU 001 Handheld Programming Unit for 6-12-18 HiScroll Vacuum Pumps. Pfeiffer P/N: PM 051 510 -T NEW Pfeiffer Handheld Key Pad HPU 001 To Communicate to Pfeiffer HiScroll Pumps. The ideal assistant for controlling and monitoring the pump parameters with graphical display. 9-pin D-sub, serial interface RS-232 for connection to the PC. RJ 45, serial interface RS-485 for connection to a Pfeiffer Vacuum Drive Unit on the HiScroll 6-12-18 Scroll Pumps. Comes with Interface cable M12/RJ 45 and RJ 45/RJ 45 for electronic drive unit, cable length 3 m. Comes with multilingual menus and graphical display. A 9 Volt block battery is required but not supplied. An OPTIONAL ACCESSORY PACK is available to include AC Power Supply Adapter, cables and CD HPU Operating Software. (Not Included with this keypad). Pfeiffer P/N PM 061 005-T. Operating Instructions can be downloaded from the side.
Condition: New
Part Number: P1011113
Price: NZ$3,564.87
Regular Price: NZ$3,752.49
Pfeiffer HiScroll 6 -12-18 Push-in fitting coupling G 1/8 including seal for hose connection (8/6 mm). Pfeiffer P/N: P 4131 029 G NEW Pfeiffer HiScroll 6 -12-18 Push-in fitting G 1/8 including seal for hose connection (8/6 mm) to be connected to an external supply with nitrogen (N2) or another dry, inert gas to this coupling.
Condition: New
Part Number: P1011114
Price: NZ$23.85
Regular Price: NZ$25.08
Pfeiffer Inlet Dust Separator for HiScroll 6-12-18 Scroll Pumps, Polyester Filter, KF25. Pfeiffer P/N: PK Z60 507NEW Pfeiffer Inlet Dust Separator for HiScroll 6-12-18 Scroll Pumps, Polyester Filter, SAS 25 S, KF25. Prevents dust particles entering into the inlet of the Scroll Pump. Allows longer service life of mechanical parts.
Condition: New
Part Number: P1011115
Price: NZ$770.39
Regular Price: NZ$810.95
Pfeiffer RPT 010 Digital Piezo Pirani Sensor for HiScroll 6-12-18 Scroll Pumps. Pfeiffer P/N: PE 100 183 -XThe HiScroll vacuum pump is equipped with a pressure sensor in the pumping system, either directly or by way of installation (optional accessory). This digital Piezo/Pirani sensor RPT 010 measures the intake pressure of the vacuum pump. Certain functions described for the vacuum pump are only available with a pressure sensor installed. This Sensor Measures coarse vaccum independent of gas type. Pressure Range 1 X 10-4 - 1200 hPa. NOTE: To connect the RPT 010 Piezo Pirani Sensor, See Operating Instructions .pdf to the left at downloads.
Condition: New
Part Number: P1011310
Price: NZ$1,549.01
Regular Price: NZ$1,630.55
Ideal Vacuum XactGauge Convection-Enhanced Pirani Gauge Kit, XGC-320 Controller, XGC-321 KF-25 Gauge, 10 ft. Sensor Cable, PS, 2 Set Points Complete Kit Includes: XactGauge XGC-320 Convection-Enhanced Controller, XGC-321 KF-25 Sensor Gauge, 3 m (10 ft.) Sensor Cable & Power Supply. Features: Inexpensive solution for Pirani type thermal conductivity gauges Convection-Enhanced Pirani sensor gauges available in 8 different flange sizes Accurate pressure measurements from 1x10-4 to 1000 Torr Compact 1/8-DIN package fits on bench or in instrument panel cutout Bright, easy to read, 4 digit OLED display Intuitive front panel controls for calibration and parameter adjustments Switch between Torr, mBar and Pa units quickly Serial RS232/RS485 DB9 I/O interface for remote control 2 set points 4 analog outputs Compatible with Granville-Phillips® 275 Convectron® and Inficon PGE050 Pirani Gauge Enhanced sensors and cables. The Ideal Vacuum XactGauge XGC-320 Convection Enhanced Pirani Gauge Controller is an inexpensive solution for simple readout of Pirani type thermal conductivity gauges with added features for ease of use and system integration. Use with any of our eight (8) XactGauge Enhanced Pirani Sensor Gauges to obtain accurate pressure measurements ranging from 1x10-4 to 1000 Torr. Our XactGauge XGC-320 Controller, conveniently housed in a compact 1/8-DIN enclosure, can be used on your benchtop or mounted in an instrument panel cutout. The bright, OLED 4 digit display is easy to read. Intuitive front panel controls allow direct gauge calibration and simple adjustment of vacuum measurement parameters. The XactGauge XGC-320 Convection-Enhanced Pirani Gauge Controller is powered by user supplied 12 to 28 VDC, 2 W, or by our XactGauge Enhanced Pirani Controller power supply. The XGC-320 Controller has a serial RS232/RS485 (DB-9) remote I/O interface, two (2) setpoints, and four (4) analog relay outputs, each rated at 1 A at 30 VDC. This XGC-320 Controller is compatible with other manufacturer’s Pirani type gauges and cables, including the Granville-Phillips® 275 Convectron® and the Inficon PGE050 Pirani Gauge Enhanced. Thermal conductivity gauges measure pressure indirectly by sensing the loss of heat from a sensor to the surrounding gas. The higher the pressure of the gas, the more heat is conducted away from the sensor. Pirani thermal conductivity gauges maintain a sensor (usually a wire) at a constant temperature and measure the current or power required to maintain that temperature. A standard Pirani gauge has a useful measuring range of about 10-4 Torr to 10 Torr. Convection-enhanced Pirani gauges take advantage of the convection current inside the sensor to extend the pressure measurement range to just above atmosphere. The XactGauge is supplied factory calibrated using Nitrogen (N2) gas. When measuring gasses other than Nitrogen/Air, accurate correction must be made for the difference in thermal conductivity between nitrogen and the gas in use, particularly at pressures above 1 Torr. DO NOT USE for explosive, corrosive or toxic gasses.
Condition: New
Part Number: P1010252
Price: NZ$2,030.85
Regular Price: NZ$2,389.24