Anest Iwata ISP-1000 Oil-Free Dry Scroll Vacuum Pump, KF-40 Inlet, 3-phase, 200-230 VAC, & 50/60 Hz. Anest Iwata Part Number: ISP-1000E-TH. The Anest Iwata ISP-1000 is economical and inexpensive to operate. Offers high performance, compact design and very light. Little routine maintenance, no oil changes, filters or foreline traps to replace. Excellent alternative to oil sealed rotary vane pumps. These Anest Iwata ISP-1000-TH oil-free dry scroll pumps operate on 3-phase, 208-230 or 380-480 VAC, & 50/60 Hz. Displacement for this Anest Iwata ISP-1000-TH is 42.4 CFM at 60 Hz. This pump has a 3-Phase motor. The part number ISP-1000E-TH specifiies Three-Phase (T) with Horizontal oriented intake flange (H). The operating instructions manual is available for down in PDF format below. Anest Iwata ISP-1000-TH oil-free dry scroll pumps have a pumping speed of 42.4 CFM at 60hz and reach an ultimate vacuum of 7.5x10-3 Torr. The Anest Iwata ISP-1000-TH is economical and inexpensive to operate, offers high performance, compact design and very light. Little routine maintenance, no oil changes, filters or foreline traps to replace make the Anest Iwata an excellent alternative to oil sealed rotary vane pumps.

Anest Iwata ISP-1000 Dry Scroll Complete Pump Module Replacement, KF-40 Inlet. Anest Iwata Part Number: VSD-1000. This Anest Iwata OEM complete pump module for the ISP-1000 dry scroll vacuum pump is an excellent alternative to sending your pump in for rebuild service.The new module is easy to install and requires only simple tools. This new module is complete with the outboard, orbiting and inboard scroll plates. A new module will turn your old pump into a new pump at a fraction of the new cost. Pump modules are new with factory 1 year warranty. Anest Iwata ISP-1000 oil-free dry scroll pumps have a pumping speed of 10.6 CFM (18 m3/hr.) at 60hz and reach an ultimate vacuum of 1x10-2 Torr. The Anest Iwata ISP-1000 is economical and inexpensive to operate, offers high performance, compact design and very light. Little routine maintenance, no oil changes, filters or foreline traps to replace make the Anest Iwata an excellent alternative to oil sealed rotary vane pumps.

Anest Iwata ISP-1000 Scroll Vacuum Pump Tip Seal Replacement Kit. Anest Iwata Part Number: 98884800. This is a tip seal kit for the Anest Iwata ISP-1000, dry scroll pumps. The tip seal kits are Anest Iwata OEM parts.

Anest Iwata Minor Repair Kit for ISP-1000 Scroll Vacuum Pumps. Anest Iwata Part Number: 98881830. This is a Minor Repair Kit for the Anest Iwata ISP-1000, dry scroll pumps. The tip seal kits are Anest Iwata OEM parts.

Anest Iwata Major Repair Kit for ISP-1000 Scroll Vacuum Pumps. Anest Iwata Part Number: 98882830. This is a Major Repair Kit for the Anest Iwata ISP-1000, dry scroll pumps. The tip seal kits are Anest Iwata OEM parts.

Anest Iwata Replacement Shaft for ISP-1000 Scroll Vacuum Pumps. Anest Iwata Part Number: 98885820. This is a Anest Iwata replacement shaft for for the Anest Iwata ISP-1000, dry scroll pumps. The replacement shafts are Anest Iwata OEM parts.

Anest Iwata Pin Crank Kit for ISP-1000 Scroll Vacuum Pumps. Anest Iwata Part Number: 98884810. This is a Anest Iwata pin crank kit for for the Anest Iwata ISP-1000, dry scroll pumps. The pin crank kits are Anest Iwata OEM parts.

Anest Iwata Bearing Kit for ISP-1000 Dry Scroll Vacuum Pumps. Anest Iwata Part Number: 98881810. This is a bearing kit for the Anest Iwata ISP-1000 Dry Scroll vacuum pumps.These Anest Iwata bearing kits are OEM products.

Anest Iwata Grease Kit for ISP-1000 Anest Iwata Dry Scroll Vacuum Pumps. Anest Iwata Part Number: 98882800. These are Anest Iwata Grease Kit for ISP-1000 Anest Iwata Dry Scroll Vacuum Pumps. These Anest Iwata grease kits are OEM products.

Foreline Trap (Black Powder Finish) for Inlet KF40 Rotary Vane Vacuum Pumps up to 80 CFM This Foreline Trap NW40 KF40 serves to prevent contaminants from entering the pump inlet and protects the system from pump fluid or particulate migration. (Backstreaming) This trap extends the life of the pump, cuts maintenance costs and helps prevent system downtime. Made of durable corrosive resistant nickel which prevents outgassing. Black powder finish. Interchangeable Filter Media is not included with this foreline trap but is available from this website. Filter Media options include, Activated Alumina, Stainless Steel Wire Mesh, Activated Carbon Granulate and Polyester Media. Common Dimensions & Specifications: Use with vacuum pumps KF40 NW40 Inlets and up to 80 CFM pumping speeds. A= 6-3/4 B= 4-1/2 C= 7-5/16

Filter Media HEPA for Foreline Trap KF40 This HEPA Media is for NW40 KF40 Foreline Traps on this website. The foreline trap canister that it fits is NW40 and our part number is P101866. This is only one HEPA media filter, the foreline trap is sold separately. This HEPA filter includes: • Reinforced with epoxy coated steel wire on both sides of cloth • Maximum oversize required to minimize pressure drop • Heavy duty industrial strength glass surrounded by heavy gauge expanded metal • Optimal sealing surface & design • Filter change out differential: 10-15 in. H2O above initial delta P • Temp (continuous): min -15° F ( -26° C) max 220° F • 99.97% removal efficiency standard to 0.3 micron • Handles hot air and oil mist from rotary vane vacuum pumps • Moisture resistant • More durable than paper media • Less maintenance • Dust loading capacity is increased 40 % - 50% with polyurethane prefilter

Exhaust Silencer for Dry Scroll Pumps or Rotary Lobe Vacuum Pumps, Flow Rate up to 23 CFM, KF25 Flange These silencers are for use on dry scroll pumps and dry rotary lobe vacuum pumps that are not connected to a house exhaust system. Such as Edwards XDS35i, Varian Agilent Tri Scroll 600, Kashiyama Neo Dry 36C and Alcatel ACP 28, ACP 28G, ACP 40, ACP 40G. They are designed for clean dry air (CDA) vacuum pumping applications where the exhaust is vented into the room. They greatly silence the exhaust of dry pumps and come with replaceable internal filter media. These media filters provide exhaust filtration to capture tip seal dust that is produced in dry scroll pumps. These exhaust silencers are equipment with an NW-25 (KF-25) vacuum flange and are rated for use up to 23 CFM. They come with a KF25 vacuum clamp and centering ring for easy installation. Also inside is a paper filter element. A replacement paper filter element is available on this website.

Filter Paper ELEMENT for Dry Pump Exhaust Silencer Kits, PN P102938, A50597001, P103344Used on Edwards XDS35i, Varian Agilent Tri Scroll 600, Kashiyama Neo Dry 36c This is a replacement filter paper element for dry pumps with exhaust silencer kits, PN P102938, A50597001, P103344, This is the filter paper element only. Black filter canister sold separately.

Ideal Vacuum XactGauge Convection-Enhanced Pirani Gauge Kit, XGC-320 Controller, XGC-321 KF-40 Gauge, 10 ft. Sensor Cable, PS, 2 Set Points Complete Kit Includes: XactGauge XGC-320 Convection-Enhanced Controller, XGC-321 KF-40 Sensor Gauge, 3 m (10 ft.) Sensor Cable & Power Supply. Features: Inexpensive solution for Pirani type thermal conductivity gauges Convection-Enhanced Pirani sensor gauges available in 8 different flange sizes Accurate pressure measurements from 1x10-4 to 1000 Torr Compact 1/8-DIN package fits on bench or in instrument panel cutout Bright, easy to read, 4 digit OLED display Intuitive front panel controls for calibration and parameter adjustments Switch between Torr, mBar and Pa units quickly Serial RS232/RS485 DB9 I/O interface for remote control 2 set points 4 analog outputs Compatible with Granville-Phillips® 275 Convectron® and Inficon PGE050 Pirani Gauge Enhanced sensors and cables. The Ideal Vacuum XactGauge XGC-320 Convection Enhanced Pirani Gauge Controller is an inexpensive solution for simple readout of Pirani type thermal conductivity gauges with added features for ease of use and system integration. Use with any of our eight (8) XactGauge Enhanced Pirani Sensor Gauges to obtain accurate pressure measurements ranging from 1x10-4 to 1000 Torr. Our XactGauge XGC-320 Controller, conveniently housed in a compact 1/8-DIN enclosure, can be used on your benchtop or mounted in an instrument panel cutout. The bright, OLED 4 digit display is easy to read. Intuitive front panel controls allow direct gauge calibration and simple adjustment of vacuum measurement parameters. The XactGauge XGC-320 Convection-Enhanced Pirani Gauge Controller is powered by user supplied 12 to 28 VDC, 2 W, or by our XactGauge Enhanced Pirani Controller power supply. The XGC-320 Controller has a serial RS232/RS485 (DB-9) remote I/O interface, two (2) setpoints, and four (4) analog relay outputs, each rated at 1 A at 30 VDC. This XGC-320 Controller is compatible with other manufacturer’s Pirani type gauges and cables, including the Granville-Phillips® 275 Convectron® and the Inficon PGE050 Pirani Gauge Enhanced. Thermal conductivity gauges measure pressure indirectly by sensing the loss of heat from a sensor to the surrounding gas. The higher the pressure of the gas, the more heat is conducted away from the sensor. Pirani thermal conductivity gauges maintain a sensor (usually a wire) at a constant temperature and measure the current or power required to maintain that temperature. A standard Pirani gauge has a useful measuring range of about 10-4 Torr to 10 Torr. Convection-enhanced Pirani gauges take advantage of the convection current inside the sensor to extend the pressure measurement range to just above atmosphere. The XactGauge is supplied factory calibrated using Nitrogen (N2) gas. When measuring gasses other than Nitrogen/Air, accurate correction must be made for the difference in thermal conductivity between nitrogen and the gas in use, particularly at pressures above 1 Torr. DO NOT USE for explosive, corrosive or toxic gasses.