MKS 627H 0.02 Torr Heated 45 °C, Absolute Baratron Capacitance Manometer, Vacuum Fitting VCR 8 Female, Accuracy 0.25% of Reading, Vertical Calibration. MKS Part Number PN: 627HU2TBE1B. The 627H Baratron® capacitance manometer is heated to 45°C, accurate to 0.12% of Reading and includes updated temperature-control electronics to provide superior long-term stability and repeatability. This capacitance manometer is available in Full Scale ranges down to 20 mTorr (0.03 mbar) to accommodate today’s lower process pressures. Based on established Baratron capacitance manometer technology, the sensor’s wetted surfaces are Inconel® for excellent resistance to corrosive gases. The contemporary stainless steel package provides a cleanroom-compatible product. The product is interchangeable with earlier 627A, 627B, 627D, and 627F Baratron capacitance manometers and can be used with MKS power supplies, display units and pressure controllers, or other compatible power supply/ readout devices. These listing is for an MKS Type 627H capacitance manometer which is heated to 45 °C, have a 15-pin D-subminiature signal connector with Thread Lock, a 0.02 Torr full scale maximum vacuum pressure reading value, a VCR 8 female vacuum flange connection, an accuracy 0.25% of reading, with vertical calibration, and have MKS part number 627HU2TBE1B. Compatible Controller and Cables: P102063 - Ideal Vacuum Cable For MKS PDR 2000 Power Supply and Digital Readout Cable 15-Pin Y Cable, Equivalent To CB2000S-1-M1 P102062 - MKS PDR 2000 Digital Power Supply and Digital Readout Capacitance Manometer Controller P1010127 - Ideal Vacuum Dual Capacitance Manometer Controller (DCM), Power Supply and Digital Pressure Readout Product Features: Excellent long-term stability Percent of Reading accuracy for more precise output signal in lower pressure ranges Full Scale ranges low as 20 mTorr (0.03 mbar) for precise measurement of low pressure processes All-Inconel corrosion-resistant wetted surfaces Faster warm-up time Visual and electrical status of temperature and heater control circuit Compatible with earlier Baratron capacitance manometers, MKS power supply/readout mod­ules, and pressure controllers Measures total pressure directly, independent of gas composition High overpressure rating for improved reliability Cleanroom-compatible stainless steel package

MKS 627H 0.05 Torr Heated 45 °C, Absolute Baratron Capacitance Manometer, Vacuum Fitting VCR 8 Female, Accuracy 0.15% of Reading, Vertical Calibration. MKS Part Number PN: 627HU5TBD1B. The 627H Baratron® capacitance manometer is heated to 45°C, accurate to 0.12% of Reading and includes updated temperature-control electronics to provide superior long-term stability and repeatability. This capacitance manometer is available in Full Scale ranges down to 20 mTorr (0.03 mbar) to accommodate today’s lower process pressures. Based on established Baratron capacitance manometer technology, the sensor’s wetted surfaces are Inconel® for excellent resistance to corrosive gases. The contemporary stainless steel package provides a cleanroom-compatible product. The product is interchangeable with earlier 627A, 627B, 627D, and 627F Baratron capacitance manometers and can be used with MKS power supplies, display units and pressure controllers, or other compatible power supply/ readout devices. These listing is for an MKS Type 627H capacitance manometer which is heated to 45 °C, have a 15-pin D-subminiature signal connector with Thread Lock, a 0.05 Torr full scale maximum vacuum pressure reading value, a VCR 8 female vacuum flange connection, an accuracy 0.15% of reading, with vertical calibration, and have MKS part number 627HU5TBD1B. Compatible Controller and Cables: P102063 - Ideal Vacuum Cable For MKS PDR 2000 Power Supply and Digital Readout Cable 15-Pin Y Cable, Equivalent To CB2000S-1-M1 P102062 - MKS PDR 2000 Digital Power Supply and Digital Readout Capacitance Manometer Controller P1010127 - Ideal Vacuum Dual Capacitance Manometer Controller (DCM), Power Supply and Digital Pressure Readout Product Features: Excellent long-term stability Percent of Reading accuracy for more precise output signal in lower pressure ranges Full Scale ranges low as 20 mTorr (0.03 mbar) for precise measurement of low pressure processes All-Inconel corrosion-resistant wetted surfaces Faster warm-up time Visual and electrical status of temperature and heater control circuit Compatible with earlier Baratron capacitance manometers, MKS power supply/readout mod­ules, and pressure controllers Measures total pressure directly, independent of gas composition High overpressure rating for improved reliability Cleanroom-compatible stainless steel package

MKS 627H 0.1 Torr Heated 45 °C, Absolute Baratron Capacitance Manometer, Vacuum Fitting VCR 8 Female, Accuracy 0.15% of Reading, Vertical Calibration. MKS Part Number PN: : 627H.1TBD1B. The 627H Baratron® capacitance manometer is heated to 45°C, accurate to 0.12% of Reading and includes updated temperature-control electronics to provide superior long-term stability and repeatability. This capacitance manometer is available in Full Scale ranges down to 20 mTorr (0.03 mbar) to accommodate today’s lower process pressures. Based on established Baratron capacitance manometer technology, the sensor’s wetted surfaces are Inconel® for excellent resistance to corrosive gases. The contemporary stainless steel package provides a cleanroom-compatible product. The product is interchangeable with earlier 627A, 627B, 627D, and 627F Baratron capacitance manometers and can be used with MKS power supplies, display units and pressure controllers, or other compatible power supply/ readout devices. These listing is for an MKS Type 627H capacitance manometer which is heated to 45 °C, have a 15-pin D-subminiature signal connector with Thread Lock, a 0.1 Torr full scale maximum vacuum pressure reading value, a VCR 8 female vacuum flange connection, an accuracy 0.15% of reading, with vertical calibration, and have MKS part number : 627H.1TBD1B. Compatible Controller and Cables: P102063 - Ideal Vacuum Cable For MKS PDR 2000 Power Supply and Digital Readout Cable 15-Pin Y Cable, Equivalent To CB2000S-1-M1 P102062 - MKS PDR 2000 Digital Power Supply and Digital Readout Capacitance Manometer Controller P1010127 - Ideal Vacuum Dual Capacitance Manometer Controller (DCM), Power Supply and Digital Pressure Readout Product Features: Excellent long-term stability Percent of Reading accuracy for more precise output signal in lower pressure ranges Full Scale ranges low as 20 mTorr (0.03 mbar) for precise measurement of low pressure processes All-Inconel corrosion-resistant wetted surfaces Faster warm-up time Visual and electrical status of temperature and heater control circuit Compatible with earlier Baratron capacitance manometers, MKS power supply/readout mod­ules, and pressure controllers Measures total pressure directly, independent of gas composition High overpressure rating for improved reliability Cleanroom-compatible stainless steel package

MKS 627H 1 Torr Heated 45 °C, Absolute Baratron Capacitance Manometer, Vacuum Fitting VCR 8 Female, Accuracy 0.12% of Reading, Vertical Calibration. MKS Part Number PN: 627H01TBC1B. The 627H Baratron® capacitance manometer is heated to 45°C, accurate to 0.12% of Reading and includes updated temperature-control electronics to provide superior long-term stability and repeatability. This capacitance manometer is available in Full Scale ranges down to 20 mTorr (0.03 mbar) to accommodate today’s lower process pressures. Based on established Baratron capacitance manometer technology, the sensor’s wetted surfaces are Inconel® for excellent resistance to corrosive gases. The contemporary stainless steel package provides a cleanroom-compatible product. The product is interchangeable with earlier 627A, 627B, 627D, and 627F Baratron capacitance manometers and can be used with MKS power supplies, display units and pressure controllers, or other compatible power supply/ readout devices. These listing is for an MKS Type 627H capacitance manometer which is heated to 45 °C, have a 15-pin D-subminiature signal connector with Thread Lock, a 1 Torr full scale maximum vacuum pressure reading value, a VCR 8 female vacuum flange connection, an accuracy 0.12% of reading, with vertical calibration, and have MKS part number 627H01TBC1B. Compatible Controller and Cables: P102063 - Ideal Vacuum Cable For MKS PDR 2000 Power Supply and Digital Readout Cable 15-Pin Y Cable, Equivalent To CB2000S-1-M1 P102062 - MKS PDR 2000 Digital Power Supply and Digital Readout Capacitance Manometer Controller P1010127 - Ideal Vacuum Dual Capacitance Manometer Controller (DCM), Power Supply and Digital Pressure Readout Product Features: Excellent long-term stability Percent of Reading accuracy for more precise output signal in lower pressure ranges Full Scale ranges low as 20 mTorr (0.03 mbar) for precise measurement of low pressure processes All-Inconel corrosion-resistant wetted surfaces Faster warm-up time Visual and electrical status of temperature and heater control circuit Compatible with earlier Baratron capacitance manometers, MKS power supply/readout mod­ules, and pressure controllers Measures total pressure directly, independent of gas composition High overpressure rating for improved reliability Cleanroom-compatible stainless steel package

MKS 627H 10 Torr Heated 45 °C, Absolute Baratron Capacitance Manometer, Vacuum Fitting VCR 8 Female, Accuracy 0.12% of Reading, Vertical Calibration. MKS Part Number PN: 627H11TBC1B. The 627H Baratron® capacitance manometer is heated to 45°C, accurate to 0.12% of Reading and includes updated temperature-control electronics to provide superior long-term stability and repeatability. This capacitance manometer is available in Full Scale ranges down to 20 mTorr (0.03 mbar) to accommodate today’s lower process pressures. Based on established Baratron capacitance manometer technology, the sensor’s wetted surfaces are Inconel® for excellent resistance to corrosive gases. The contemporary stainless steel package provides a cleanroom-compatible product. The product is interchangeable with earlier 627A, 627B, 627D, and 627F Baratron capacitance manometers and can be used with MKS power supplies, display units and pressure controllers, or other compatible power supply/ readout devices. These listing is for an MKS Type 627H capacitance manometer which is heated to 45 °C, have a 15-pin D-subminiature signal connector with Thread Lock, a 10 Torr full scale maximum vacuum pressure reading value, a VCR 8 female vacuum flange connection, an accuracy 0.12% of reading, with vertical calibration, and have MKS part number 627H11TBC1B. Compatible Controller and Cables: P102063 - Ideal Vacuum Cable For MKS PDR 2000 Power Supply and Digital Readout Cable 15-Pin Y Cable, Equivalent To CB2000S-1-M1 P102062 - MKS PDR 2000 Digital Power Supply and Digital Readout Capacitance Manometer Controller P1010127 - Ideal Vacuum Dual Capacitance Manometer Controller (DCM), Power Supply and Digital Pressure Readout Product Features: Excellent long-term stability Percent of Reading accuracy for more precise output signal in lower pressure ranges Full Scale ranges low as 20 mTorr (0.03 mbar) for precise measurement of low pressure processes All-Inconel corrosion-resistant wetted surfaces Faster warm-up time Visual and electrical status of temperature and heater control circuit Compatible with earlier Baratron capacitance manometers, MKS power supply/readout mod­ules, and pressure controllers Measures total pressure directly, independent of gas composition High overpressure rating for improved reliability Cleanroom-compatible stainless steel package

MKS 627H 100 Torr Heated 45 °C, Absolute Baratron Capacitance Manometer, Vacuum Fitting VCR 8 Female, Accuracy 0.12% of Reading, Vertical Calibration. MKS Part Number PN: 627H12TBC1B. The 627H Baratron® capacitance manometer is heated to 45°C, accurate to 0.12% of Reading and includes updated temperature-control electronics to provide superior long-term stability and repeatability. This capacitance manometer is available in Full Scale ranges down to 20 mTorr (0.03 mbar) to accommodate today’s lower process pressures. Based on established Baratron capacitance manometer technology, the sensor’s wetted surfaces are Inconel® for excellent resistance to corrosive gases. The contemporary stainless steel package provides a cleanroom-compatible product. The product is interchangeable with earlier 627A, 627B, 627D, and 627F Baratron capacitance manometers and can be used with MKS power supplies, display units and pressure controllers, or other compatible power supply/ readout devices. These listing is for an MKS Type 627H capacitance manometer which is heated to 45 °C, have a 15-pin D-subminiature signal connector with Thread Lock, a 100 Torr full scale maximum vacuum pressure reading value, a VCR 8 female vacuum flange connection, an accuracy 0.12% of reading, with vertical calibration, and have MKS part number 627H12TBC1B. Compatible Controller and Cables: P102063 - Ideal Vacuum Cable For MKS PDR 2000 Power Supply and Digital Readout Cable 15-Pin Y Cable, Equivalent To CB2000S-1-M1 P102062 - MKS PDR 2000 Digital Power Supply and Digital Readout Capacitance Manometer Controller P1010127 - Ideal Vacuum Dual Capacitance Manometer Controller (DCM), Power Supply and Digital Pressure Readout Product Features: Excellent long-term stability Percent of Reading accuracy for more precise output signal in lower pressure ranges Full Scale ranges low as 20 mTorr (0.03 mbar) for precise measurement of low pressure processes All-Inconel corrosion-resistant wetted surfaces Faster warm-up time Visual and electrical status of temperature and heater control circuit Compatible with earlier Baratron capacitance manometers, MKS power supply/readout mod­ules, and pressure controllers Measures total pressure directly, independent of gas composition High overpressure rating for improved reliability Cleanroom-compatible stainless steel package

MKS 627H 1,000 Torr Heated 45 °C, Absolute Baratron Capacitance Manometer, Vacuum Fitting VCR 8 Female, Accuracy 0.12% of Reading, Vertical Calibration. MKS Part Number PN: 627H13TBC1B. The 627H Baratron® capacitance manometer is heated to 45°C, accurate to 0.12% of Reading and includes updated temperature-control electronics to provide superior long-term stability and repeatability. This capacitance manometer is available in Full Scale ranges down to 20 mTorr (0.03 mbar) to accommodate today’s lower process pressures. Based on established Baratron capacitance manometer technology, the sensor’s wetted surfaces are Inconel® for excellent resistance to corrosive gases. The contemporary stainless steel package provides a cleanroom-compatible product. The product is interchangeable with earlier 627A, 627B, 627D, and 627F Baratron capacitance manometers and can be used with MKS power supplies, display units and pressure controllers, or other compatible power supply/ readout devices. These listing is for an MKS Type 627H capacitance manometer which is heated to 45 °C, have a 15-pin D-subminiature signal connector with Thread Lock, a 1,000 Torr full scale maximum vacuum pressure reading value, a VCR 8 female vacuum flange connection, an accuracy 0.12% of reading, with vertical calibration, and have MKS part number 627H13TBC1B. Compatible Controller and Cables: P102063 - Ideal Vacuum Cable For MKS PDR 2000 Power Supply and Digital Readout Cable 15-Pin Y Cable, Equivalent To CB2000S-1-M1 P102062 - MKS PDR 2000 Digital Power Supply and Digital Readout Capacitance Manometer Controller P1010127 - Ideal Vacuum Dual Capacitance Manometer Controller (DCM), Power Supply and Digital Pressure Readout Product Features: Excellent long-term stability Percent of Reading accuracy for more precise output signal in lower pressure ranges Full Scale ranges low as 20 mTorr (0.03 mbar) for precise measurement of low pressure processes All-Inconel corrosion-resistant wetted surfaces Faster warm-up time Visual and electrical status of temperature and heater control circuit Compatible with earlier Baratron capacitance manometers, MKS power supply/readout mod­ules, and pressure controllers Measures total pressure directly, independent of gas composition High overpressure rating for improved reliability Cleanroom-compatible stainless steel package

MKS Manometer Cable Connects 937B or 946 Controllers to 626 or 627 Manometers, 10 ft. (3m) Long. MKS Part Number: 100007555. The MKS vacuum gauge signal cable connects 937B or 946 controllers to 626 or 627 manometers. It has 9-pin type D subminiature and 15-pin type D subminiature connectors. This is the Cable ONLY. The Series 937B Digital Combination Vacuum Gauge Controller operates up to six vacuum pressure sensors simultaneously. This highly flexible vacuum gauge controller supports a wide range of sensor technologies, including cold cathode, hot cathode, standard Pirani, convection Pirani, Baratron® capacitance manometers and absolute Piezo sensors for a measurement range from ultra-high vacuum to above atmospheric pressure. The back lit LCD display, intuitive menus and simple push button front panel, allows for ease in setup of the 937B. The 937B, enables the use of any sensor card in each of the sensor card slots. The 937B can be configured with up to three hot or cold cathode type gauges, or three dual sensor cards for a maximum of six gauge connections.

MKS Manometer Cable Connects 937B or 946 Controllers to 626 or 627 Manometers, 25 ft. (7.5m). Long. MKS Part Number: 100007556. The MKS vacuum gauge signal cable connects 937B or 946 controllers to 626 or 627 manometers. It has 9-pin type D subminiature and 15-pin type D subminiature connectors. This is the Cable ONLY. The Series 937B Digital Combination Vacuum Gauge Controller operates up to six vacuum pressure sensors simultaneously. This highly flexible vacuum gauge controller supports a wide range of sensor technologies, including cold cathode, hot cathode, standard Pirani, convection Pirani, Baratron® capacitance manometers and absolute Piezo sensors for a measurement range from ultra-high vacuum to above atmospheric pressure. The back lit LCD display, intuitive menus and simple push button front panel, allows for ease in setup of the 937B. The 937B, enables the use of any sensor card in each of the sensor card slots. The 937B can be configured with up to three hot or cold cathode type gauges, or three dual sensor cards for a maximum of six gauge connections.

IVP Dual Capacitance Manometer Gauge Controller with USB for MKS Baratron Gauges, LCD Readout and Two Setpoints. The Ideal Vacuum Products (IVP) XGC-520 Dual Capacitance Manometer Gauge Controller is an inexpensive solution for pressure readout of up to two Capacitance Diaphragm Gauges. This IVP exclusive controller provides enhanced accuracy with intelligently designed features for simple user control and easy system integration. The controller is designed to interface with the popular 626D, 627H, and 722C series of Baratron® capacitance diaphragm gauges from MKS and can read full scale absolute vacuum/pressure ranges from 20 mTorr (2 x 10-4 Torr) to as much as 10,000 Torr (1x104 Torr). Because these gauges measure absolute pressure, they are gas type and composition independent. Lookup tables and conversion factors are not required. The unit has two analog output relays, each of which can be assigned to either of the two gauge channels and programmed to energize when a setpoint is reached. This flexibility allows the user to easily set up automated tasks, such as valve activation or energizing a turbomolecular pump when an appropriate backing pump pressure is achieved. The Dual Capacitance Manometer Gauge Controller is conveniently housed in a compact 1/8-DIN extruded aluminum enclosure for benchtop or rack panel mounting. The brilliant, blue LCD display is easy to read and displays vital system and controller information at a glance. The intuitive front panel membrane switch interface allows the user to access and adjust all parameters quickly. Remote communication and control is achieved by RS-232 serial terminal software. Connection is made via the rear-mounted DB15 or USB-B connectors. A variety of sensor and serial cables are available. The controller has a built-in universal power supply which accepts an input of 100-240 VAC, 50/60Hz. Included is a 2 meter long (6 ft.) 115 VAC input power cord with US plug 5-15P to C13 Connector. Features: Controls up to two (2) capacitive diaphragm sensor gauges (CDG) Interfaces with all popular MKS 626D, 627H, and 722C series Baratron sensor gauges, heated or unheated, with full scale measurement ranges from 20 mTorr to 10,000 Torr Gas type and composition independent - no need for lookup tables and conversion factors Compact 1/8-DIN enclosure for benchtop or rack panel mounting Brilliant Blue LCD readout display Intuitive interface makes setting parameters quick and easy Two setpoint output relays for automated control of other equipment User selectable pressure units for each gauge (Torr, mTorr, mBar, and Pa) Serial communication for remote control through DB9 and USB-B ports Available Cables and Adapters: P102063 Sensor cable, connects two gauges to DCM,10 ft., DB9 -M to two DB15-F P102061 Sensor cable, connects two gauges to DCM, 10 ft. DB9-M to two DB9-F P1011364 Serial cable, connects remote computer to DCM, 10 ft., DB15-M to DB9-F P1012796 USB cable, connects remote computer to DCM, 10 ft. USB-A to USB-B P1012800 DB15-M to terminal block breakout for splitting out relays and RS232 cables Please download the user manual for complete information.

IVP Cable For XGC-520 and MKS PDR2000 Controller, Dual Sensor Y Cable, DB9M to Two DB15F, Equivalent To CB2000S-1-M1. This is a dual sensor cable for the Ideal Vacuum XGC-520 Dual Capacitance Manometer Gauge Controller (P1010127) and the MKS PDR2000 (P102062). It connects the controller to up to two Baratron sensors with DB15 pinouts. This Y splitter cable has a DB9 male on one end which connects to the controller, and two DB15 female connectors on the other. This cable is manufactured by Ideal Vacuum and is a direct replacement for MKS part number CB2000S-1-M1. Ths cable is compatible with Baratron models127, 128, 626, 627, 628 or 722 series sensors with 15 pin male connectors. These cables are 10 feet long.

MKS PDR2000 Power Supply and Digital Readout Capacitance Manometer Controller. MKS Part Number: PDR2000AO. The MKS PDR2000 power supply and digital readout capacitance manometer controller provides up to 750mA to operate two Baratron pressure transducers. The MKS PDR 200 can display one channel at a time on a 4-1/2 digital meter readout. The MKS PDR 2000 has two configurable relay set points, an RS-232 output, and a 0 to 10 VDC linear output for each transducer. Cables for the MKS PDR 2000 are available but sold separately.

Adapter KF-16 to 8 VCR Male, ISO-KF Flange Size NW-16, Stainless Steel These adapters connect KF-16 to Swagelok® 8 VCR® male. The flange size follows ISO-KF standards and is NW-16. They are commonly used to make connections between ISO-KF fittings and VCR Tubing. The ISO-KF flanges are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Stainless Steel. Adapter KF-16 to 8 VCR Male, ISO-KF Flange Size NW-16, Stainless Steel Flange Size: ISO-KF NW-16 Tubing Size: 8 VCR (1/2 inch) Common Dimensions: A = .1.63 (41mm), B = .41 (10mm) Swagelok, VCR-TM Swagelok Company

Adapter KF-25 to 8 VCR Male, ISO-KF Flange Size NW-25, Stainless Steel These adapters connect KF-25 to Swagelok® 8 VCR® male. The flange size follows ISO-KF standards and is NW-25. They are commonly used to make connections between ISO-KF fittings and VCR Tubing. The ISO-KF flanges are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Stainless Steel. VCR® is a registered trademark brand name of tube fitting providing by The Swagelok Company. Adapter KF-25 to 8 VCR Male, ISO-KF Flange Size NW-25, Stainless Steel Flange Size: ISO-KF NW-25 Tubing Size: 8 VCR (1/2 inch) Common Dimensions: A = 1.60 (41mm), B = .41 (10mm) Swagelok, VCR-TM Swagelok Company

Adapter KF-40 to 8 VCR Male, ISO-KF Flange Size NW-40, Stainless Steel These adapters connect KF-40 to Swagelok® 8 VCR® male. The flange size follows ISO-KF standards and is NW-40. They are commonly used to make connections between ISO-KF fittings and VCR Tubing. The ISO-KF flanges are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Stainless Steel. Adapter KF-40 to 8 VCR Male, ISO-KF Flange Size NW-40, Stainless Steel Flange Size: ISO-KF NW-40 Tubing Size: 8 VCR (1/2 inch) Common Dimensions: A = 1.60 (41mm), B = .41 (10mm) Swagelok, VCR-TM Swagelok Company

Adapter KF-50 to 8 VCR Male, ISO-KF Flange Size NW-50, Stainless Steel These adapters connect KF-50 to Swagelok® 8 VCR® male. The flange size follows ISO-KF standards and is NW-50. They are commonly used to make connections between ISO-KF fittings and VCR Tubing. The ISO-KF flanges are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Stainless Steel. Adapter KF-50 to 8 VCR Male, ISO-KF Flange Size NW-50, Stainless Steel Flange Size: ISO-KF NW-50 Tubing Size: 8 VCR (1/2 inch) Common Dimensions: A = 1.60 (41mm), B = .41 (10mm) Swagelok, VCR-TM Swagelok Company

Swagelok SS-8-VCR-2-VS, VCR 8, 1/2 in 316L Stainless Steel Unplated Nonretained Gasket. PN: SS-8-VCR-2-VS This Swagelok® VCR® Unplated Nonretained Gasket is made of 316L Stainless Steel. Swagelok Part Number: SS-8-VCR-2-VS. These VCR (Vacuum Coupling Radiation) fittings and components are precision manufactured and offer a leak-tight, metal on metal seal. They can be used for any fluid flow application and provide leak-tight service from vacuum to positive pressure. Polished surface finish and high purity materials virtually eliminate these fittings as a source of system contamination. The VCR fitting design has been tested to maximum leak rate of 4x10-9 std cm3/s with silver-plated-copper gaskets, and to a maximum leak rate of 4x10-11 std cm3/s with unplated (Ni, Cu or 316L SS) gaskets.Specifications and Dimensions:316L Stainless Steel VCR Size: 8 Inch Size: 1/2 E: 0.44 in (11.2 mm) Tx: 0.78 in (19.8 mm) Swagelok, VCR-TM Swagelok Company

Swagelok NI-8-VCR-2-VS, VCR 8, 1/2 in Nickel Unplated Nonretained Gasket. PN: NI-8-VCR-2-VS This Swagelok® VCR® Unplated Nonretained Gasket is made of Nickel. Swagelok Part Number: NI-8-VCR-2-VS. These VCR (Vacuum Coupling Radiation) fittings and components are precision manufactured and offer a leak-tight, metal on metal seal. They can be used for any fluid flow application and provide leak-tight service from vacuum to positive pressure. Polished surface finish and high purity materials virtually eliminate these fittings as a source of system contamination. The VCR fitting design has been tested to maximum leak rate of 4x10-9 std cm3/s with silver-plated-copper gaskets, and to a maximum leak rate of 4x10-11 std cm3/s with unplated (Ni, Cu or 316L SS) gaskets.Specifications and Dimensions:Nickel VCR Size: 8 Inch Size: 1/2 E: 0.44 in (11.2 mm) Tx: 0.78 in (19.8 mm) Swagelok, VCR-TM Swagelok Company

Swagelok NI-8-VCR-2, VCR 8, 1/2 in, Silver Plated Nickel, Nonretained Gasket This Swagelok® VCR® Nonretained Gasket is made of Silver Plated Nickel. Swagelok Part Number: NI-8-VCR-2. These VCR (Vacuum Coupling Radiation) fittings and components are precision manufactured and offer a leak-tight, metal on metal seal. They can be used for any fluid flow application and provide leak-tight service from vacuum to positive pressure. Polished surface finish and high purity materials virtually eliminate these fittings as a source of system contamination. The VCR fitting design has been tested to maximum leak rate of 4x10-9 std cm3/s with silver-plated-copper gaskets, and to a maximum leak rate of 4x10-11 std cm3/s with unplated (Ni, Cu or 316L SS) gaskets.Specifications and Dimensions:Silver Plated Nickel VCR Size: 8 Inch Size: 1/2 E: 0.44 in (11.2 mm) Tx: 0.78 in (19.8 mm) Swagelok, VCR-TM Swagelok Company

Swagelok VCR 8, 1/2 in Copper Unplated Nonretained Gasket. PN: CU-8-VCR-2 This Swagelok® VCR® Unplated Nonretained Gasket is made of Copper. Swagelok Part Number: CU-8-VCR-2. These VCR (Vacuum Coupling Radiation) fittings and components are precision manufactured and offer a leak-tight, metal on metal seal. They can be used for any fluid flow application and provide leak-tight service from vacuum to positive pressure. Polished surface finish and high purity materials virtually eliminate these fittings as a source of system contamination. The VCR fitting design has been tested to maximum leak rate of 4x10-9 std cm3/s with silver-plated-copper gaskets, and to a maximum leak rate of 4x10-11 std cm3/s with unplated (Ni, Cu or 316L SS) gaskets.Specifications and Dimensions:Copper VCR Size: 8 Inch Size: 1/2 E: 0.44 in (11.2 mm) Tx: 0.78 in (19.8 mm) Swagelok, VCR-TM Swagelok Company

Conflat Flange (CF) VCR Male 1/2 inch connected to CF 1-1/3 inch, Stainless Steel Fittings These conflat to male Swagelok® VCR® vacuum fittings have a flange size of ConFlat (CF) 1-1/3 inch connected to Swagelok male VCR 1/2 inch. ConFlat (CF) flanges are used for ultra-high vacuum applications. These fittings use a copper gasket and knife-edge flanges to achieve the high vacuum seal and can operate down to 10-13 torr (10-11 Pa) and can be heated to 450 °C for bake-out. North American flange sizes are given by flange outer diameter in inches: 1-1/3 (mini conflat), 2¾, 4½, 6, 8, 10, 12, 13¼, 14 and 16½. In Europe and Asia, sizes are given by tube inner diameter in millimeters: DN16, DN40, DN63, DN100, DN160, DN200, DN250. These vacuum fittings are made of corrosion resistant stainless steel. Conflat Flange (CF) VCR Male 1/2 inch to CF 1-1/3 inch, Stainless Steel Fittings CF Flange Size: CF 1-1/3 inch to VCR Male 1/2 inch Common Dimensions: A= Length 1.55 inch B= Tube Size 1/2 inch Swagelok, VCR-TM Swagelok Company

Conflat Flange (CF) VCR Male 1/2 inch connected to CF 2-3/4 inch, Stainless Steel Fittings These conflat to male Swagelok® VCR® vacuum fittings have a flange size of ConFlat (CF) 2-3/4 inch connected to Swagelok male VCR 1/2 inch. ConFlat (CF) flanges are used for ultra-high vacuum applications. These fittings use a copper gasket and knife-edge flanges to achieve the high vacuum seal and can operate down to 10-13 torr (10-11 Pa) and can be heated to 450 °C for bake-out. North American flange sizes are given by flange outer diameter in inches: 1-1/3 (mini conflat), 2¾, 4½, 6, 8, 10, 12, 13¼, 14 and 16½. In Europe and Asia, sizes are given by tube inner diameter in millimeters: DN16, DN40, DN63, DN100, DN160, DN200, DN250. These vacuum fittings are made of corrosion resistant stainless steel. Conflat Flange (CF) VCR Male 1/2 inch to CF 2-3/4 inch, Stainless Steel Fittings CF Flange Size: CF 2-3/4 inch to VCR Male 1/2 inch Common Dimensions: A= Length 1.71 inch B= Tube Size 1/2 inch Swagelok, VCR-TM Swagelok Company

Conflat Flange (CFF) Copper Gaskets CF Size 1-1/3" These conflat copper conflat gaskets fit a conflat flange size of 1-1/3 inches. ConFlat (CF) flanges are used for ultra-high vacuum applications. These fittings use a copper gasket and knife-edge flanges to achieve the high vacuum seal and can operate down to 10-13 torr (10-11 Pa) and can be heated to 450°C for bake-out. North American flange sizes are given by flange outer diameter in inches: 1-1/3 ("mini conflat"), 2¾, 4½, 6, 8, 10, 12, 13¼, 14 and 16½. In Europe and Asia, sizes are given by tube inner diameter in millimeters: DN16, DN40, DN63, DN100, DN160, DN200, DN250. These vacuum fittings are made of corrosive resistant stainless steel.Conflat Flange (CF) Copper Gaskets CF Size 1-1/3" - 1 eachCF Flange Size: CF 1-1/3 inch Common Dimensions: Flange Outer Diameter (OD) 1-1/3", Gasket Outer Diameter (OD) 0.838", Gasket Inner Diameter (ID) 0.640"

Conflat Flange (CFF) Copper Gaskets CF Size 2-3/4" These conflat copper conflat gaskets fit a conflat flange size of 2-3/4 inches. ConFlat (CF) flanges are used for ultra-high vacuum applications. These fittings use a copper gasket and knife-edge flanges to achieve the high vacuum seal and can operate down to 10-13 torr (10-11 Pa) and can be heated to 450°C for bake-out. North American flange sizes are given by flange outer diameter in inches: 1-1/3 ("mini conflat"), 2¾, 4½, 6, 8, 10, 12, 13¼, 14 and 16½ , in Europe and Asia, sizes are given by tube inner diameter in millimeters: DN16, DN40, DN63, DN100, DN160, DN200, DN250. These vacuum fittings are made of corrosive resistant stainless steel. Conflat Flange (CF) Copper Gaskets CF Size 2-3/4" - 1 eachCF Flange Size: CF 2-3/4 inch Common Dimensions: Flange Outer Diameter (OD) 2-3/4", Gasket Outer Diameter (OD) 1.895", Gasket Inner Diameter (ID) 1.451"

Bolt Kit For 1.33 (1-1/3)Inch Conflat Clear Bolt Hole Flanges, Silver-Plated Allen Bolts With Platenuts.These bolt kits contain silver-plated 12-point head bolts, platenuts, and washers to fasten clearance hole 1.33 (1-1/3) inch CF Conflat flanged fittings. These confalt flages can be pumped down to 10-13 torr (10-11 Pa) and can be heated to 450 °C for bake-out. North American flange sizes are given by flange outer diameter in inches: 1-1/3 ("mini conflat"), 2-1/8, 2-3/4, 4-1/2, 4-5/8, 6, 6-3/4, 8, 10, 12, 13-1/4, 14 and 16-1/2. In Europe and Asia, sizes are given by tube inner diameter in millimeters: DN16, DN40, DN63, DN100, DN160, DN200, DN250. These are complete kits, with bolts, washers, and platenuts to fasten one conflat clearance hole 1.33 (1-1/3) inch flange connection.Complete Kit - 1.33 (1-1/3) inch Conflat Clearance Bolt Hole Fasteners: QTY 6, Silver-Plated 8-32 x 0.75 Inch Long Allen Bolts QTY 6, Washers QTY 3, Platenut

Bolt Kit For 2.75 (2-3/4)Inch Conflat Clear Bolt Hole Flanges, Silver-Plated 12 Point Bolts With Platenuts.These bolt kits contain silver-plated 12-point head bolts, platenuts, and washers to fasten clearance hole 2.75 (2-3/4) inch CF Conflat flanged fittings. These confalt flages can be pumped down to 10-13 torr (10-11 Pa) and can be heated to 450 °C for bake-out. North American flange sizes are given by flange outer diameter in inches: 1-1/3 ("mini conflat"), 2-1/8, 2-3/4, 4-1/2, 4-5/8, 6, 6-3/4, 8, 10, 12, 13-1/4, 14 and 16-1/2. In Europe and Asia, sizes are given by tube inner diameter in millimeters: DN16, DN40, DN63, DN100, DN160, DN200, DN250. These are complete kits, with bolts, washers, and platenuts to fasten one conflat clearance hole 2.75 (2-3/4) inch flange connection.Complete Kit - 2.75 (2-3/4) inch Conflat Clearance Bolt Hole Fasteners: QTY 6, Silver-Plated 1/4 x 1.25 Inch Long 12-Point Bolts QTY 6, Washers QTY 3, Platenut

Hinge Clamp KF-10, KF-16 Vacuum Fittings, ISO-KF Flange Size NW-10, NW-16, AluminumThese KF-10, KF-16 Hinge Clamp vacuum fittings follow ISO-KF standards and have a flange size of NW-10, NW-16. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Aluminum.KF-10, KF-16 Hinge ClampISO-KF Flange Size: NW-16Common Dimensions: A=2.45" (62.30mm)B=1.61" (41mm)C=0.649" (16.5mm)

Hinge Clamp KF-25 Vacuum Fittings, ISO-KF Flange Size NW-25, AluminumThese KF-25 Hinge Clamp vacuum fittings follow ISO-KF standards and have a flange size of NW-25. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Aluminum.KF-25 Hinge ClampISO-KF Flange Size: NW-25Common Dimensions:A=2.85" (72.40mm)B=2.12" (54mm)C=0.649" (16.50mm)

Hinge Clamp KF-40 Vacuum Fittings, ISO-KF Flange Size NW-40, AluminumThese KF-40 Hinge Clamp vacuum fittings follow ISO-KF standards and have a flange size of NW-40. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Aluminum.KF-40 Hinge ClampISO-KF Flange Size: NW-40Common Dimensions:A=3.53" (89.70mm)B=2.71" (69mm)C=0.649" (16.50mm)

Hinge Clamp KF-50 Vacuum Fittings, ISO-KF Flange Size NW-50, AluminumThese KF-50 Hinge Clamp vacuum fittings follow ISO-KF standards and have a flange size of NW-50. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of Aluminum.KF-50 Hinge ClampISO-KF Flange Size: NW-50Common Dimensions:A=4.49 (114.00mm)B=3.54 (90mm)C=0.846 (21.50mm)

Centering Ring KF-16 Vacuum Fittings, ISO-KF Flange Size NW-16, Stainless Steel & Viton® O-RingThese KF-16 Centering Ring vacuum fittings follow ISO-KF standards and have a flange size of NW-16. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of corrosive resistant stainless steel with Viton® O-Ring. Viton® is well known for its excellent resistance to heat (400°F/200°C) and to aggressive fuels and chemicals. Viton® is a registered trademark of DuPont Performance Elastomers.KF-16 Centering Ring with Viton® O-RingISO-KF Flange Size: NW-16

Centering Ring KF-25 Vacuum Fittings, ISO-KF Flange Size NW-25, Stainless Steel & Viton® O-ringThese KF-25 Centering Ring vacuum fittings follow ISO-KF standards and have a flange size of NW-25. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of corrosive resistant stainless steel with Viton® O-Ring. Viton® is well known for its excellent resistance to heat (400°F/200°C) and to aggressive fuels and chemicals. Viton® is a registered trademark of DuPont Performance Elastomers.KF-25 Centering Ring with Viton® O-RingISO-KF Flange Size: NW-25

Centering Ring KF-40 Vacuum Fittings, ISO-KF Flange Size NW-40, Stainless Steel & Viton® O-ringThese KF-40 Centering Ring vacuum fittings follow ISO-KF standards and have a flange size of NW-40. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of corrosive resistant stainless steel with Viton® O-Ring. Viton® is well known for its excellent resistance to heat (400°F/200°C) and to aggressive fuels and chemicals. Viton® is a registered trademark of DuPont Performance Elastomers.KF-40 Centering Ring with Viton® O-RingISO-KF Flange Size: NW-40

Centering Ring KF-50 Vacuum Fittings, ISO-KF Flange Size NW-50, Stainless Steel & Viton®These KF-50 Centering Ring vacuum fittings follow ISO-KF standards and have a flange size of NW-50. They are commonly used to build foreline vacuum plumbing and process systems. They are often called quick flange fittings because they are quick to assemble. A circumferential clamp and centering ring form the vacuum seal between the connecting flanges (please see top right figure - click to enlarge). The centering ring contains a rubber elastomer o-ring. The standard sizes for quick flange fittings are KF-10, KF-16, KF-25, KF-40, and KF-50 with flange sizes NW-10, NW-16, NW-25, NW-40, and NW-50, respectively. They are made of corrosive resistant stainless steel with Viton® O-Ring. Viton® is well known for its excellent resistance to heat (400°F/200°C) and to aggressive fuels and chemicals. Viton® is a registered trademark of DuPont Performance Elastomers.KF-50 Centering Ring with Viton® O-RingISO-KF Flange Size: NW-50